CY7C64013C
CY7C64113C
Full-Speed USB (12-Mbps) Function
Full-Speed USB (12-Mbps) Function
Cypress Semiconductor Corporation
Document #: 38-08001 Rev. *B
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 3, 2006
CY7C64013C
CY7C64113C
TABLE OF CONTENTS
16.6 DAC Interrupt ..........................................................................................................................31
16.7 GPIO/HAPI Interrupt ...............................................................................................................32
16.8 I2C Interrupt .............................................................................................................................32
17.1 USB Serial Interface Engine (SIE) ..........................................................................................33
17.2 USB Enumeration ...................................................................................................................33
19.0 USB MODE TABLES ...................................................................................................................39
20.0 REGISTER SUMMARY ................................................................................................................43
24.0 SWITCHING CHARACTERISTICS (fOSC = 6.0 MHz) ...................................................................................... 46
25.0 ORDERING INFORMATION ........................................................................................................48
Document #: 38-08001 Rev. *B
Page 3 of 51
CY7C64013C
CY7C64113C
LIST OF FIGURES
Figure 9-6. GPIO Configuration Register...............................................................................................20
Figure 10-2. DAC Port Data...................................................................................................................22
Figure 10-4. DAC Port Interrupt Enable.................................................................................................23
Figure 12-1. HAPI/I2C Configuration Register.......................................................................................24
Figure 13-1. I2C Data Register...............................................................................................................25
Figure 13-2. I2C Status and Control Register........................................................................................25
Figure 18-1. USB Device Address Registers.........................................................................................34
Figure 18-5. Token/Data Packet Flow Diagram.....................................................................................38
Figure 24-1. Clock Timing......................................................................................................................47
Figure 24-2. USB Data Signal Timing....................................................................................................47
Figure 24-4. HAPI Write by External Device to USB Microcontroller.....................................................48
Document #: 38-08001 Rev. *B
Page 4 of 51
CY7C64013C
CY7C64113C
LIST OF TABLES
Table 4-1. Pin Assignments ..................................................................................................................10
Table 4-2. I/O Register Summary .........................................................................................................10
Table 9-1. GPIO Port Output Control Truth Table and Interrupt Polarity ..............................................20
Table 12-2. I2C Port Configuration ........................................................................................................25
Table 13-1. I2C Status and Control Register Bit Definitions ..................................................................26
Table 14-1. Port 2 Pin and HAPI Configuration Bit Definitions .............................................................27
Table 18-1. Memory Allocation for Endpoints ......................................................................................35
Table 19-1. USB Register Mode Encoding ...........................................................................................39
Table 19-2. Details of Modes for Differing Traffic Conditions (see Table 19-1 for the decode legend) ........... 41
Document #: 38-08001 Rev. *B
Page 5 of 51
CY7C64013C
CY7C64113C
1.0
Features
• Full-speed USB Microcontroller
• 8-bit USB Optimized Microcontroller
— Harvard architecture
— 6-MHz external clock source
— 12-MHz internal CPU clock
— 48-MHz internal clock
• Internal memory
— 256 bytes of RAM
— 8 KB of PROM (CY7C64013C, CY7C64113C)
2
• Integrated Master/Slave I C-compatible Controller (100 kHz) enabled through General-Purpose I/O (GPIO) pins
• Hardware Assisted Parallel Interface (HAPI) for data transfer to external devices
• I/O ports
— Three GPIO ports (Port 0 to 2) capable of sinking 7 mA per pin (typical)
—An additional GPIO port (Port 3) capable of sinking 12 mA per pin (typical) for high current requirements: LEDs
— Higher current drive achievable by connecting multiple GPIO pins together to drive a common output
— EachGPIOport can be configured asinputs withinternalpull-ups or open drain outputsor traditional CMOS outputs
— A Digital to Analog Conversion (DAC) port with programmable current sink outputs is available on the CY7C64113C
devices
— Maskable interrupts on all I/O pins
• 12-bit free-running timer with one microsecond clock ticks
• Watchdog Timer (WDT)
• Internal Power-On Reset (POR)
• USB Specification Compliance
— Conforms to USB Specification, Version 1.1
— Conforms to USB HID Specification, Version 1.1
—Supports up to five user configured endpoints
Up to four 8-byte data endpoints
Up to two 32-byte data endpoints
— Integrated USB transceivers
• Improved output drivers to reduce EMI
• Operating voltage from 4.0V to 5.5V DC
• Operating temperature from 0 to 70 degrees Celsius
— CY7C64013C available in 28-pin SOIC and 28-pin PDIP packages
— CY7C64113C available in 48-pin SSOP packages
• Industry-standard programmer support
Document #: 38-08001 Rev. *B
Page 6 of 51
CY7C64013C
CY7C64113C
2.0
Functional Overview
The CY7C64013C and CY7C64113C are 8-bit One Time Programmable microcontrollers that are designed for full-speed USB
applications. The instruction set has been optimized specifically for USB operations, although the microcontrollers can be used
for a variety of non-USB embedded applications.
GPIO
The CY7C64013C features 19 GPIO pins to support USB and other applications. The I/O pins are grouped into three ports
(P0[7:0], P1[2:0], P2[6:2], P3[2:0]) where each port can be configured as inputs with internal pull-ups, open drain outputs, or
traditional CMOS outputs. There are 16 GPIO pins (Ports 0 and 1) which are rated at 7 mA typical sink current. Port 3 pins are
rated at 12 mA typical sink current, a current sufficient to drive LEDs. Multiple GPIO pins can be connected together to drive a
single output for more drive current capacity. Additionally, each GPIO can be used to generate a GPIO interrupt to the microcon-
troller. All of the GPIO interrupts share the same “GPIO” interrupt vector.
The CY7C64113C has 32 GPIO pins (P0[7:0], P1[7:0], P2[7:0], P3[7:0])
DAC
The CY7C64113C has four programmable sink current I/O pins (DAC) pins (P4[7,2:0]). Every DAC pin includes an integrated 14-
kΩ pull-up resistor. When a ‘1’ is written to a DAC I/O pin, the output current sink is disabled and the output pin is driven HIGH
by the internal pull-up resistor. When a ‘0’ is written to a DAC I/O pin, the internal pull-up resistor is disabled and the output pin
provides the programmed amount of sink current. A DAC I/O pin can be used as an input with an internal pull-up by writing a ‘1’
to the pin.
The sink current for each DAC I/O pin can be individually programmed to one of 16 values using dedicated Isink registers. DAC
bits P4[1:0] can be used as high-current outputs with a programmable sink current range of 3.2 to 16 mA (typical). DAC bits
P4[7,2] have a programmable current sink range of 0.2 to 1.0 mA (typical). Multiple DAC pins can be connected together to drive
a single output that requires more sink current capacity. Each I/O pin can be used to generate a DAC interrupt to the microcon-
troller. Also, the interrupt polarity for each DAC I/O pin is individually programmable.
Clock
The microcontroller uses an external 6-MHz crystal and an internal oscillator to provide a reference to an internal PLL-based
clock generator. This technology allows the customer application to use an inexpensive 6-MHz fundamental crystal that reduces
the clock-related noise emissions (EMI). A PLL clock generator provides the 6-, 12-, and 48-MHz clock signals for distribution
within the microcontroller.
Memory
The CY7C64013C and CY7C64113C have 8 KB of PROM.
Power on Reset, Watchdog and Free running Time
These parts include power-on reset logic, a Watchdog timer, and a 12-bit free-running timer. The power-on reset (POR) logic
detects when power is applied to the device, resets the logic to a known state, and begins executing instructions at PROM address
0x0000. The Watchdog timer is used to ensure the microcontroller recovers after a period of inactivity. The firmware may become
inactive for a variety of reasons, including errors in the code or a hardware failure such as waiting for an interrupt that never occurs.
I2C and HAPI Interface
2
The microcontroller can communicate with external electronics through the GPIO pins. An I C-compatible interface accommo-
dates a 100-kHz serial link with an external device. There is also a Hardware Assisted Parallel Interface (HAPI) which can be
used to transfer data to an external device.
Timer
The free-running 12-bit timer clocked at 1 MHz provides two interrupt sources, 128-µs and 1.024-ms. The timer can be used to
measure the duration of an event under firmware control by reading the timer at the start of the event and after the event is
complete. The difference between the two readings indicates the duration of the event in microseconds. The upper four bits of
the timer are latched into an internal register when the firmware reads the lower eight bits. A read from the upper four bits actually
reads data from the internal register, instead of the timer. This feature eliminates the need for firmware to try to compensate if the
upper four bits increment immediately after the lower eight bits are read.
Interrupts
The microcontroller supports 11 maskable interrupts in the vectored interrupt controller. Interrupt sources include the USB Bus
Reset interrupt, the 128-µs (bit 6) and 1.024-ms (bit 9) outputs from the free-running timer, five USB endpoints, the DAC port, the
2
GPIO ports, and the I C-compatible master mode interface. The timer bits cause an interrupt (if enabled) when the bit toggles
from LOW ‘0’ to HIGH ‘1.’ The USB endpoints interrupt after the USB host has written data to the endpoint FIFO or after the USB
controller sends a packet to the USB host. The DAC ports have an additional level of masking that allows the user to select which
DAC inputs can cause a DAC interrupt. The GPIO ports also have a level of masking to select which GPIO inputs can cause a
GPIO interrupt. For additional flexibility, the input transition polarity that causes an interrupt is programmable for each pin of the
DAC port. Input transition polarity can be programmed for each GPIO port as part of the port configuration. The interrupt polarity
can be rising edge (‘0’ to ‘1’) or falling edge (‘1’ to ‘0’).
Document #: 38-08001 Rev. *B
Page 7 of 51
CY7C64013C
CY7C64113C
Logic Block Diagram
6-MHz crystal
PLL
48 MHz
Clock
12-MHz
8-bit
CPU
USB
Transceiver
Divider
D+[0]
D–[0]
USB
SIE
Upstream
USB Port
12 MHz
Interrupt
Controller
PROM
8 KB
RAM
256 byte
GPIO
PORT 0
P0[7:0]
P1[2:0]
P1[7:3]
6 MHz
GPIO
PORT 1
12-bit
Timer
CY7C64113C only
P2[0,1,7]
GPIO/
HAPI
Watchdog
Timer
P2[2]; Latch_Empty
P2[3]; Data_Ready
P2[4]; STB
PORT 2
P2[5]; OE
P2[6]; CS
Power-On
Reset
High Current
P3[2:0]
Outputs
GPIO
Additional
High Current
Outputs
PORT 3
P3[7:3]
DAC[0]
DAC
PORT
DAC[2]
DAC[7]
CY7C64113C only
2
SCLK
SDATA
I C
Interface
2
*I C-compatible interface enabled by firmware through
P2[1:0] or P1[1:0]
Document #: 38-08001 Rev. *B
Page 8 of 51
CY7C64013C
CY7C64113C
3.0
Pin Configurations
TOP VIEW
CY7C64013C
28-pin SOIC
CY7C64013C
28-pin PDIP
CY7C64113C
48-pin SSOP
XTALOUT
XTALIN
1
2
3
4
28
27
26
XTALOUT
XTALIN
1
2
3
4
48
47
46
V
V
CC
XTALOUT
XTALIN
1
2
3
4
28
27
26
V
CC
CC
P1[1]
P1[0]
P1[2]
P3[0]
P3[2]
GND
P2[2]
P1[1]
P1[0]
P1[2]
P1[4]
P1[6]
P3[0]
P3[2]
P1[0]
P1[2]
P3[0]
P3[2]
P2[2]
GND
P2[4]
V
V
V
REF
REF
REF
GND
P3[1]
D+[0]
D–[0]
P2[3]
P2[5]
P0[7]
P0[5]
P0[3]
P0[1]
P0[6]
25
24
23
22
21
20
19
18
17
16
15
P1[3]
P1[5]
P1[7]
P3[1]
D+[0]
D–[0]
P3[3]
GND
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
P1[1]
GND
P3[1]
D+[0]
D–[0]
P2[3]
P2[5]
P0[7]
P0[5]
P0[3]
P0[1]
25
24
23
22
21
20
19
18
17
16
15
5
5
5
6
6
6
7
7
7
8
8
8
9
P2[4]
P2[6]
9
GND
P3[4]
NC
9
P2[6]
10
11
12
13
14
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
10
11
12
13
14
V
PP
V
P0[0]
P0[2]
P0[4]
P0[6]
PP
P0[0]
P0[2]
P0[4]
P3[5]
P3[7]
P2[1]
P2[3]
GND
P3[6]
P2[0]
P2[2]
GND
P2[4]
P2[6]
DAC[0]
P2[5]
P2[7]
DAC[7]
P0[7]
P0[5]
P0[3]
P0[1]
DAC[1]
V
PP
P0[0]
P0[2]
P0[4]
P0[6]
DAC[2]
Document #: 38-08001 Rev. *B
Page 9 of 51
CY7C64013C
CY7C64113C
4.0
4.1
Product Summary Tables
Pin Assignments
Table 4-1. Pin Assignments
Name
D+[0], D–[0]
P0
I/O
I/O
I/O
28-Pin SOIC
6, 7
28-Pin PDIP
7, 8
48-Pin SSOP
7, 8
Description
Upstream port, USB differential data.
P0[7:0]
P0[7:0]
P0[7:0]
GPIO Port 0 capable of sinking 7 mA (typical).
10, 14, 11, 15, 11, 15, 12, 16, 20, 26, 21, 27,
12, 16, 13, 17 13, 17, 14, 18 22, 28, 23, 29
P1
I/O
I/O
I/O
I/O
P1[2:0]
25, 27, 26
P1[2:0]
26, 4, 27
P1[7:0]
6, 43, 5, 44,
4, 45, 47, 46
GPIO Port 1 capable of sinking 7 mA (typical).
P2
P2[6:2]
19, 9, 20, 8,
21
P2[6:2]
20, 10, 21,
9, 23
P2[7:0]
GPIO Port 2 capable of sinking 7 mA (typical). HAPI
18, 32, 17, 33, is also supported through P2[6:2].
15, 35, 14, 36
P3
P3[2:0]
23, 5, 24
P3[2:0]
24, 6, 25
P3[7:0]
13, 37, 12, 39,
10, 41, 7, 42
GPIO Port 3, capable of sinking 12 mA (typical).
DAC
DAC[7,2:0]
DAC Port with programmable current sink outputs.
19, 25, 24, 31 DAC[1:0] offer a programmable range of 3.2 to 16 mA
typical. DAC[7,2] have a programmable sink current
range of 0.2 to 1.0 mA typical.
XTAL
XTAL
IN
OUT
IN
2
1
2
1
2
1
6-MHz crystal or external clock input.
6-MHz crystal out.
IN
OUT
V
18
19
30
Programming voltage supply, tie to ground during
normal operation.
PP
V
IN
IN
IN
28
4, 22
3
28
5, 22
3
48
Voltage supply.
CC
GND
11, 16, 34, 40 Ground.
V
3
External 3.3V supply voltage for the differential data
REF
output buffers and the D+ pull-up.
NC
38
No Connect.
4.2
I/O Register Summary
I/O registers are accessed via the I/O Read (IORD) and I/O Write (IOWR, IOWX) instructions. IORD reads data from the selected
port into the accumulator. IOWR performs the reverse; it writes data from the accumulator to the selected port. Indexed I/O Write
(IOWX) adds the contents of X to the address in the instruction to form the port address and writes data from the accumulator to
the specified port. Specifying address 0 (e.g., IOWX 0h) means the I/O register is selected solely by the contents of X.
All undefined registers are reserved. It is important not to write to reserved registers as this may cause an undefined operation
or increased current consumption during operation. When writing to registers with reserved bits, the reserved bits must be written
with ‘0.’
Table 4-2. I/O Register Summary
Register Name
Port 0 Data
I/O Address Read/Write
Function
Page
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
R/W
R/W
R/W
R/W
W
GPIO Port 0 Data
GPIO Port 1 Data
GPIO Port 2 Data
GPIO Port 3 Data
Port 1 Data
Port 2 Data
Port 3 Data
Port 0 Interrupt Enable
Port 1 Interrupt Enable
Port 2 Interrupt Enable
Port 3 Interrupt Enable
Interrupt Enable for Pins in Port 0
Interrupt Enable for Pins in Port 1
Interrupt Enable for Pins in Port 2
Interrupt Enable for Pins in Port 3
W
W
W
Document #: 38-08001 Rev. *B
Page 10 of 51
CY7C64013C
CY7C64113C
Table 4-2. I/O Register Summary (continued)
Register Name
I/O Address Read/Write
Function
GPIO Port Configurations
Page
GPIO Configuration
0x08
0x09
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x1F
0x20
0x21
0x24
0x25
0x26
0x28
0x29
0x30
0x31
0x32
0x38-0x3F
0x40
0x41
0x42
0x43
0x44
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
0x50
0x51
0xFF
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
2
2
HAPI and I C Configuration
HAPI Width and I C Position Configuration
USB Device Address A
USB Device Address A
EP A0 Counter Register
EP A0 Mode Register
EP A1 Counter Register
EP A1 Mode Register
EP A2 Counter Register
EP A2 Mode Register
USB Status & Control
Global Interrupt Enable
Endpoint Interrupt Enable
Timer (LSB)
USB Address A, Endpoint 0 Counter
USB Address A, Endpoint 0 Configuration
USB Address A, Endpoint 1 Counter
USB Address A, Endpoint 1 Configuration
USB Address A, Endpoint 2 Counter
USB Address A, Endpoint 2 Configuration
USB Upstream Port Traffic Status and Control
Global Interrupt Enable
USB Endpoint Interrupt Enables
Lower 8 Bits of Free-running Timer (1 MHz)
Upper 4 Bits of Free-running Timer
Watchdog Timer Clear
Timer (MSB)
R
WDT Clear
W
2
2
I C Control & Status
R/W
R/W
R/W
W
I C Status and Control
2
2
I C Data
I C Data
DAC Data
DAC Data
DAC Interrupt Enable
DAC Interrupt Polarity
DAC Isink
Interrupt Enable for each DAC Pin
W
Interrupt Polarity for each DAC Pin
W
Input Sink Current Control for each DAC Pin
Reserved
Reserved
EP A3 Counter Register
EP A3 Mode Register
EP A4 Counter Register
EP A4 Mode Register
Reserved
R/W
R/W
R/W
R/W
USB Address A, Endpoint 3 Counter
USB Address A, Endpoint 3 Configuration
USB Address A, Endpoint 4 Counter
USB Address A, Endpoint 4 Configuration
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Processor Status & Control
R/W
Microprocessor Status and Control Register
Document #: 38-08001 Rev. *B
Page 11 of 51
CY7C64013C
CY7C64113C
4.3
Instruction Set Summary
Refer to the CYASM Assembler User’s Guide for more details.
Table 4-3. Instruction Set Summary
MNEMONIC
HALT
operand opcode cycles
MNEMONIC
NOP
operand opcode cycles
00
01
7
4
6
7
4
6
7
4
6
7
4
6
7
4
6
7
4
6
7
4
6
7
5
7
8
4
5
6
4
5
20
21
4
4
4
7
8
4
4
7
8
5
5
4
4
5
5
5
5
5
6
7
8
7
8
7
8
6
4
4
4
4
4
8
4
4
8
5
5
7
14
ADD A,expr
ADD A,[expr]
ADD A,[X+expr]
ADC A,expr
ADC A,[expr]
ADC A,[X+expr]
SUB A,expr
SUB A,[expr]
SUB A,[X+expr]
SBB A,expr
SBB A,[expr]
SBB A,[X+expr]
OR A,expr
data
INC A
acc
direct
index
data
02
INC X
x
22
03
INC [expr]
INC [X+expr]
DEC A
direct
index
acc
23
04
24
direct
index
data
05
25
06
DEC X
x
26
07
DEC [expr]
DEC [X+expr]
IORD expr
IOWR expr
POP A
direct
index
address
address
27
direct
index
data
08
28
09
29
0A
2A
direct
index
data
0B
2B
0C
0D
0E
POP X
2C
2D
2E
PUSH A
PUSH X
SWAP A,X
SWAP A,DSP
MOV [expr],A
MOV [X+expr],A
OR [expr],A
OR [X+expr],A
AND [expr],A
AND [X+expr],A
XOR [expr],A
XOR [X+expr],A
IOWX [X+expr]
CPL
OR A,[expr]
OR A,[X+expr]
AND A,expr
AND A,[expr]
AND A,[X+expr]
XOR A,expr
XOR A,[expr]
XOR A,[X+expr]
CMP A,expr
CMP A,[expr]
CMP A,[X+expr]
MOV A,expr
MOV A,[expr]
MOV A,[X+expr]
MOV X,expr
MOV X,[expr]
reserved
direct
index
data
0F
2F
10
30
direct
index
data
11
direct
index
direct
index
direct
index
direct
index
index
31
12
32
13
33
direct
index
data
14
34
15
35
16
36
direct
index
data
17
37
18
38
19
39
direct
index
data
1A
3A
1B
ASL
3B
1C
1D
1E
ASR
3C
3D
3E
direct
RLC
RRC
XPAGE
1F
4
4
RET
3F
MOV A,X
40
DI
70
MOV X,A
41
4
EI
72
MOV PSP,A
CALL
60
4
RETI
73
addr
addr
addr
addr
addr
50 - 5F
80-8F
90-9F
A0-AF
B0-BF
10
5
JC
addr
addr
addr
addr
C0-CF
D0-DF
E0-EF
F0-FF
JMP
JNC
CALL
10
5
JACC
JZ
INDEX
JNZ
5
Document #: 38-08001 Rev. *B
Page 12 of 51
CY7C64013C
CY7C64113C
5.0
5.1
Programming Model
14-Bit Program Counter (PC)
The 14-bit program counter (PC) allows access to up to 8 KB of PROM available with the CY7C64x13C architecture. The top 32
bytes of the ROM in the 8 Kb part are reserved for testing purposes. The program counter is cleared during reset, such that the
first instruction executed after a reset is at address 0x0000h. Typically, this is a jump instruction to a reset handler that initializes
The lower eight bits of the program counter are incremented as instructions are loaded and executed. The upper six bits of the
program counter are incremented by executing an XPAGE instruction. As a result, the last instruction executed within a 256-byte
“page” of sequential code should be an XPAGE instruction. The assembler directive “XPAGEON” causes the assembler to insert
XPAGE instructions automatically. Because instructions can be either one or two bytes long, the assembler may occasionally
need to insert a NOP followed by an XPAGE to execute correctly.
The address of the next instruction to be executed, the carry flag, and the zero flag are saved as two bytes on the program stack
during an interrupt acknowledge or a CALL instruction. The program counter, carry flag, and zero flag are restored from the
program stack during a RETI instruction. Only the program counter is restored during a RET instruction.
The program counter cannot be accessed directly by the firmware. The program stack can be examined by reading SRAM from
location 0x00 and up.
Document #: 38-08001 Rev. *B
Page 13 of 51
CY7C64013C
CY7C64113C
5.1.1
Program Memory Organization
after reset
14-bit PC
Address
0x0000
Program execution begins here after a reset
0x0002
0x0004
0x0006
0x0008
0x000A
0x000C
0x000E
0x0010
0x0012
0x0014
0x0016
0x0018
0x001A
USB Bus Reset interrupt vector
128-µs timer interrupt vector
1.024-ms timer interrupt vector
USB address A endpoint 0 interrupt vector
USB address A endpoint 1 interrupt vector
USB address A endpoint 2 interrupt vector
USB address A endpoint 3 interrupt vector
USB address A endpoint 4 interrupt vector
Reserved
DAC interrupt vector
GPIO interrupt vector
2
I C interrupt vector
Program Memory begins here
0x1FDF
8 KB (-32) PROM ends here (CY7C64013C, CY7C64113C)
Document #: 38-08001 Rev. *B
Page 14 of 51
CY7C64013C
CY7C64113C
5.2
8-Bit Accumulator (A)
The accumulator is the general-purpose register for the microcontroller.
5.3
8-Bit Temporary Register (X)
The “X” register is available to the firmware for temporary storage of intermediate results. The microcontroller can perform indexed
5.4
8-Bit Program Stack Pointer (PSP)
During a reset, the program stack pointer (PSP) is set to 0x00 and “grows” upward from this address. The PSP may be set by
firmware, using the MOV PSP,A instruction. The PSP supports interrupt service under hardware control and CALL, RET, and
RETI instructions under firmware control. The PSP is not readable by the firmware.
During an interrupt acknowledge, interrupts are disabled and the 14-bit program counter, carry flag, and zero flag are written as
two bytes of data memory. The first byte is stored in the memory addressed by the PSP, then the PSP is incremented. The second
byte is stored in memory addressed by the PSP, and the PSP is incremented again. The overall effect is to store the program
counter and flags on the program “stack” and increment the PSP by two.
The Return from Interrupt (RETI) instruction decrements the PSP, then restores the second byte from memory addressed by the
PSP. The PSP is decremented again and the first byte is restored from memory addressed by the PSP. After the program counter
and flags have been restored from stack, the interrupts are enabled. The overall effect is to restore the program counter and flags
from the program stack, decrement the PSP by two, and reenable interrupts.
The Call Subroutine (CALL) instruction stores the program counter and flags on the program stack and increments the PSP by
two.
The Return from Subroutine (RET) instruction restores the program counter but not the flags from the program stack and decre-
ments the PSP by two.
5.4.1
Data Memory Organization
The CY7C64x13C microcontrollers provide 256 bytes of data RAM. Normally, the SRAM is partitioned into four areas: program
stack, user variables, data stack, and USB endpoint FIFOs. The following is one example of where the program stack, data stack,
and user variables areas could be located.
After reset
8-bit DSP 8-bit PSP
Address
0x00
Program Stack Growth
(Move DSP
)
user selected
Data Stack Growth
8-bit DSP
User variables
[2]
USB FIFO space for five endpoints
0xFF
Notes:
Document #: 38-08001 Rev. *B
Page 15 of 51
CY7C64013C
CY7C64113C
5.5
8-Bit Data Stack Pointer (DSP)
The data stack pointer (DSP) supports PUSH and POP instructions that use the data stack for temporary storage. A PUSH
instruction pre-decrements the DSP, then writes data to the memory location addressed by the DSP. A POP instruction reads
data from the memory location addressed by the DSP, then post-increments the DSP.
During a reset, the DSP is reset to 0x00. A PUSH instruction when DSP equals 0x00 writes data at the top of the data RAM
(address 0xFF). This writes data to the memory area reserved for USB endpoint FIFOs. Therefore, the DSP should be indexed
at an appropriate memory location that does not compromise the Program Stack, user-defined memory (variables), or the USB
endpoint FIFOs.
For USB applications, the firmware should set the DSP to an appropriate location to avoid a memory conflict with RAM dedicated
to USB FIFOs. The memory requirements for the USB endpoints are described in Section 18.2. Example assembly instructions
to do this with two device addresses (FIFOs begin at 0xD8) are shown below:
MOV A,20h
; Move 20 hex into Accumulator (must be D8h or less)
SWAP A,DSP ; swap accumulator value into DSP register
5.6
Address Modes
The CY7C64013C and CY7C64113C microcontrollers support three addressing modes for instructions that require data
operands: data, direct, and indexed.
5.6.1
Data (Immediate)
“Data” address mode refers to a data operand that is actually a constant encoded in the instruction. As an example, consider the
instruction that loads A with the constant 0xD8:
• MOV A,0D8h
This instruction requires two bytes of code where the first byte identifies the “MOV A” instruction with a data operand as the
second byte. The second byte of the instruction is the constant “0xD8.” A constant may be referred to by name if a prior “EQU”
statement assigns the constant value to the name. For example, the following code is equivalent to the example shown above:
• DSPINIT: EQU 0D8h
• MOV A,DSPINIT
5.6.2
Direct
“Direct” address mode is used when the data operand is a variable stored in SRAM. In that case, the one byte address of the
variable is encoded in the instruction. As an example, consider an instruction that loads A with the contents of memory address
location 0x10:
• MOV A,[10h]
Normally, variable names are assigned to variable addresses using “EQU” statements to improve the readability of the assembler
source code. As an example, the following code is equivalent to the example shown above:
• buttons: EQU 10h
• MOV A,[buttons]
5.6.3
Indexed
“Indexed” address mode allows the firmware to manipulate arrays of data stored in SRAM. The address of the data operand is
the sum of a constant encoded in the instruction and the contents of the “X” register. Normally, the constant is the “base” address
of an array of data and the X register contains an index that indicates which element of the array is actually addressed:
• array: EQU 10h
• MOV X,3
• MOV A,[X+array]
This would have the effect of loading A with the fourth element of the SRAM “array” that begins at address 0x10. The fourth
element would be at address 0x13.
Document #: 38-08001 Rev. *B
Page 16 of 51
CY7C64013C
CY7C64113C
6.0
Clocking
XTALOUT
(pin 1)
XTALIN
(pin 2)
To Internal PLL
30 pF
30 pF
Figure 6-1. Clock Oscillator On-Chip Circuit
The XTALIN and XTALOUT are the clock pins to the microcontroller. The user can connect an external oscillator or a crystal to
these pins. When using an external crystal, keep PCB traces between the chip leads and crystal as short as possible (less than
2 cm). A 6-MHz fundamental frequency parallel resonant crystal can be connected to these pins to provide a reference frequency
for the internal PLL. The two internal 30-pF load caps appear in series to the external crystal and would be equivalent to a 15-pF
load. Therefore, the crystal must have a required load capacitance of about 15–18 pF. A ceramic resonator does not allow the
microcontroller to meet the timing specifications of full speed USB and therefore a ceramic resonator is not recommended with
these parts.
An external 6-MHz clock can be applied to the XTALIN pin if the XTALOUT pin is left open. Grounding the XTALOUT pin when
driving XTALIN with an oscillator does not work because the internal clock is effectively shorted to ground.
7.0
Reset
The CY7C64x13C supports two resets: Power-On Reset (POR) and a Watchdog Reset (WDR). Each of these resets causes:
• all registers to be restored to their default states,
• the USB Device Address to be set to 0,
• all interrupts to be disabled,
• the PSP and Data Stack Pointer (DSP) to be set to memory address 0x00.
The occurrence of a reset is recorded in the Processor Status and Control Register, as described in Section 15.0. Bits 4 and 6
are used to record the occurrence of POR and WDR, respectively. Firmware can interrogate these bits to determine the cause
of a reset.
Program execution starts at ROM address 0x0000 after a reset. Although this looks like interrupt vector 0, there is an important
difference. Reset processing does NOT push the program counter, carry flag, and zero flag onto program stack. The firmware
reset handler should configure the hardware before the “main” loop of code. Attempting to execute a RET or RETI in the firmware
reset handler causes unpredictable execution results.
7.1
Power-On Reset (POR)
When V is first applied to the chip, the Power-On Reset (POR) signal is asserted and the CY7C64x13C enters a “semi-suspend”
CC
state. During the semi-suspend state, which is different from the suspend state defined in the USB specification, the oscillator
and all other blocks of the part are functional, except for the CPU. This semi-suspend time ensures that both a valid V level is
CC
reached and that the internal PLL has time to stabilize before full operation begins. When the V has risen above approximately
CC
2.5V, and the oscillator is stable, the POR is deasserted and the on-chip timer starts counting. The first 1 ms of suspend time is
not interruptible, and the semi-suspend state continues for an additional 95 ms unless the count is bypassed by a USB Bus Reset
on the upstream port. The 95 ms provides time for V to stabilize at a valid operating voltage before the chip executes code.
CC
If a USB Bus Reset occurs on the upstream port during the 95-ms semi-suspend time, the semi-suspend state is aborted and
program execution begins immediately from address 0x0000. In this case, the Bus Reset interrupt is pending but not serviced
until firmware sets the USB Bus Reset Interrupt Enable bit (bit 0 of register 0x20) and enables interrupts with the EI command.
The POR signal is asserted whenever V drops below approximately 2.5V, and remains asserted until V rises above this level
CC
CC
again. Behavior is the same as described above.
7.2
The Watchdog Timer Reset (WDR) occurs when the internal Watchdog timer rolls over. Writing any value to the write-only
Watchdog Restart Register at address 0x26 clears the timer. The timer rolls over and WDR occurs if it is not cleared within t
Watchdog Reset (WDR)
WATCH
(8 ms minimum) of the last clear. Bit 6 of the Processor Status and Control Register is set to record this event (the register contents
are set to 010X0001 by the WDR). A Watchdog Timer Reset lasts for 2 ms, after which the microcontroller begins execution at
ROM address 0x0000.
Document #: 38-08001 Rev. *B
Page 17 of 51
CY7C64013C
CY7C64113C
2 ms
t
WATCH
Last write to
Watchdog Timer
Register
No write to WDT
register, so WDR
goes HIGH
Execution begins at
Reset Vector 0x0000
Figure 7-1. Watchdog Reset (WDR)
The USB transmitter is disabled by a Watchdog Reset because the USB Device Address Register is cleared (see Section 18.1).
Otherwise, the USB Controller would respond to all address 0 transactions.
It is possible for the WDR bit of the Processor Status and Control Register (0xFF) to be set following a POR event. The WDR bit
should be ignored If the firmware interrogates the Processor Status and Control Register for a Set condition on the WDR bit and
if the POR (bit 3 of register 0xFF) bit is set.
8.0
Suspend Mode
The CY7C64x13C can be placed into a low-power state by setting the Suspend bit of the Processor Status and Control register.
All logic blocks in the device are turned off except the GPIO interrupt logic and the USB receiver. The clock oscillator and PLL,
as well as the free-running and Watchdog timers, are shut down. Only the occurrence of an enabled GPIO interrupt or non-idle
bus activity at a USB upstream or downstream port wakes the part out of suspend. The Run bit in the Processor Status and
Control Register must be set to resume a part out of suspend.
The clock oscillator restarts immediately after exiting suspend mode. The microcontroller returns to a fully functional state 1 ms
after the oscillator is stable. The microcontroller executes the instruction following the I/O write that placed the device into suspend
mode before servicing any interrupt requests.
The GPIO interrupt allows the controller to wake-up periodically and poll system components while maintaining a very low average
power consumption. To achieve the lowest possible current during suspend mode, all I/O should be held at V or Gnd. This also
CC
applies to internal port pins that may not be bonded in a particular package.
Typical code for entering suspend is shown below:
...
...
; All GPIO set to low-power state (no floating pins)
; Enable GPIO interrupts if desired for wake-up
; Set suspend and run bits
; Write to Status and Control Register - Enter suspend, wait for USB activity (or GPIO Interrupt)
; This executes before any ISR
mov a, 09h
iowr FFh
nop
...
; Remaining code for exiting suspend routine
Document #: 38-08001 Rev. *B
Page 18 of 51
CY7C64013C
CY7C64113C
9.0
General-Purpose I/O (GPIO) Ports
V
CC
GPIO
CFG
mode
2-bits
OE
Q2
Q1
Data
Internal
Data Bus
Out
Latch
14 kΩ
GPIO
PIN
Port Write
Q3*
Data
Port Read
In
Latch
Reg_Bit
STRB
(Latch is Transparent
except in HAPI mode)
Data
Interrupt
Latch
Interrupt
Enable
*Port 0,1,2: Low I
Port 3: High I
sink
sink
Interrupt
Controller
Figure 9-1. Block Diagram of a GPIO Pin
There are up to 32 GPIO pins (P0[7:0], P1[7:0], P2[7:0], and P3[7:0]) for the hardware interface. The number of GPIO pins
changes based on the package type of the chip. Each port can be configured as inputs with internal pull-ups, open drain outputs,
or traditional CMOS outputs. Port 3 offers a higher current drive, with typical current sink capability of 12 mA. The data for each
GPIO port is accessible through the data registers. Port data registers are shown in Figure 9-2 through Figure 9-5, and are set
to 1 on reset.
Port 0 Data
ADDRESS 0x00
Bit #
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
P0.7
R/W
1
P0.6
R/W
1
P0.5
R/W
1
P0.4
R/W
1
P0.3
R/W
1
P0.2
R/W
1
P0.1
R/W
1
P0.0
R/W
1
Figure 9-2. Port 0 Data
Port 1 Data
Bit #
ADDRESS 0x01
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
P1.7
R/W
1
P1.6
R/W
1
P1.5
R/W
1
P1.4
R/W
1
P1.3
R/W
1
P1.2
R/W
1
P1.1
R/W
1
P1.0
R/W
1
Figure 9-3. Port 1 Data
Port 2 Data
Bit #
ADDRESS 0x02
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
P2.7
R/W
1
P2.6
R/W
1
P2.5
R/W
1
P2.4
R/W
1
P2.3
R/W
1
P2.2
R/W
1
P2.1
R/W
1
P2.0
R/W
1
Figure 9-4. Port 2 Data
Document #: 38-08001 Rev. *B
Page 19 of 51
CY7C64013C
CY7C64113C
Port 3 Data
Bit #
ADDRESS 0x03
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
P3.7
R/W
1
P3.6
R/W
1
P3.5
R/W
1
P3.4
R/W
1
P3.3
R/W
1
P32
R/W
1
P3.1
R/W
1
P3.0
R/W
1
Figure 9-5. Port 3 Data
Special care should be taken with any unused GPIO data bits. An unused GPIO data bit, either a pin on the chip or a port bit that
is not bonded on a particular package, must not be left floating when the device enters the suspend state. If a GPIO data bit is
left floating, the leakage current caused by the floating bit may violate the suspend current limitation specified by the USB
Specifications. If a ‘1’ is written to the unused data bit and the port is configured with open drain outputs, the unused data bit
remains in an indeterminate state. Therefore, if an unused port bit is programmed in open-drain mode, it must be written with a
‘0.’ Notice that the CY7C64013C part always requires that the data bits P1[7:3], P2[7,1,0], and P3[7:3] be written with a ‘0.’
In normal non-HAPI mode, reads from a GPIO port always return the present state of the voltage at the pin, independent of the
settings in the Port Data Registers. If HAPI mode is activated for a port, reads of that port return latched data as controlled by the
HAPI signals (see Section 14.0). During reset, all of the GPIO pins are set to a high-impedance input state (‘1’ in open drain
mode). Writing a ‘0’ to a GPIO pin drives the pin LOW. In this state, a ‘0’ is always read on that GPIO pin unless an external source
overdrives the internal pull-down device.
9.1
GPIO Configuration Port
Every GPIO port can be programmed as inputs with internal pull-ups, outputs LOW or HIGH, or Hi-Z (floating, the pin is not driven
internally). In addition, the interrupt polarity for each port can be programmed. The Port Configuration bits (Figure 9-6) and the
Interrupt Enable bit (Figure 9-7 through Figure 9-10) determine the interrupt polarity of the port pins.
GPIO Configuration
Bit #
ADDRESS 0x08
7
6
5
4
3
2
1
0
Bit Name
Port 3
Config Bit 1
Port 3
Config Bit 0
Port 2
Config Bit 1
Port 2
Config Bit 0
Port 1
Config Bit 1
Port 1
Config Bit 0
Port 0
Config Bit 1
Port 0
Config Bit 0
Read/Write
Reset
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Figure 9-6. GPIO Configuration Register
As shown in Table 9-1 below, a positive polarity on an input pin represents a rising edge interrupt (LOW to HIGH), and a negative
polarity on an input pin represents a falling edge interrupt (HIGH to LOW).
The GPIO interrupt is generated when all of the following conditions are met: the Interrupt Enable bit of the associated Port
Interrupt Enable Register is enabled, the GPIO Interrupt Enable bit of the Global Interrupt Enable Register (Figure 16-1) is
enabled, the Interrupt Enable Sense (bit 2, Figure 15-1) is set, and the GPIO pin of the port sees an event matching the interrupt
polarity.
The driving state of each GPIO pin is determined by the value written to the pin’s Data Register (Figure 9-2 through Figure 9-5)
and by its associated Port Configuration bits as shown in the GPIO Configuration Register (Figure 9-6). These ports are configured
on a per-port basis, so all pins in a given port are configured together. The possible port configurations are detailed in Table 9-1.
As shown in this table below, when a GPIO port is configured with CMOS outputs, interrupts from that port are disabled.
During reset, all of the bits in the GPIO Configuration Register are written with ‘0’ to select Hi-Z mode for all GPIO ports as the
default configuration.
Table 9-1. GPIO Port Output Control Truth Table and Interrupt Polarity
Port Config Bit 1 Port Config Bit 0 Data Register Output Drive Strength Interrupt Enable Bit
Interrupt Polarity
Disabled
1
1
0
0
1
0
1
0
0
1
0
1
0
1
0
1
Output LOW
Resistive
0
1
0
1
0
1
0
1
– (Falling Edge)
Disabled
Output LOW
Output HIGH
Output LOW
Hi-Z
Disabled
Disabled
– (Falling Edge)
Disabled
Output LOW
Hi-Z
+ (Rising Edge)
Document #: 38-08001 Rev. *B
Page 20 of 51
CY7C64013C
CY7C64113C
Q1, Q2, and Q3 discussed below are the transistors referenced in Figure 9-1. The available GPIO drive strength are:
• Output LOW Mode: The pin’s Data Register is set to ‘0’
Writing ‘0’ to the pin’s Data Register puts the pin in output LOW mode, regardless of the contents of the Port Configuration
Bits[1:0]. In this mode, Q1 and Q2 are OFF. Q3 is ON. The GPIO pin is driven LOW through Q3.
• Output HIGH Mode: The pin’s Data Register is set to 1 and the Port Configuration Bits[1:0] is set to ‘10’
In this mode, Q1 and Q3 are OFF. Q2 is ON. The GPIO is pulled up through Q2. The GPIO pin is capable of sourcing... of
current.
• Resistive Mode: The pin’s Data Register is set to 1 and the Port Configuration Bits[1:0] is set to ‘11’
Q2 and Q3 are OFF. Q1 is ON. The GPIO pin is pulled up with an internal 14kΩ resistor. In resistive mode, the pin may serve
as an input. Reading the pin’s Data Register returns a logic HIGH if the pin is not driven LOW by an external source.
• Hi-Z Mode: The pin’s Data Register is set to1 and Port Configuration Bits[1:0] is set either ‘00’ or ‘01’
Q1, Q2, and Q3 are all OFF. The GPIO pin is not driven internally. In this mode, the pin may serve as an input. Reading the
Port Data Register returns the actual logic value on the port pins.
9.2
GPIO Interrupt Enable Ports
Each GPIO pin can be individually enabled or disabled as an interrupt source. The Port 0–3 Interrupt Enable registers provide
this feature with an interrupt enable bit for each GPIO pin. When HAPI mode (discussed in Section 14.0) is enabled the GPIO
interrupts are blocked, including ports not used by HAPI, so GPIO pins cannot be used as interrupt sources.
During a reset, GPIO interrupts are disabled by clearing all of the GPIO interrupt enable ports. Writing a ‘1’ to a GPIO Interrupt
Enable bit enables GPIO interrupts from the corresponding input pin. All GPIO pins share a common interrupt, as discussed in
Section 16.7
Port 0 Interrupt Enable
Bit #
ADDRESS 0x04
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
P0.7 Intr Enable P0.6 Intr Enable P0.5 Intr Enable P0.4 Intr Enable P0.3 Intr Enable P0.2 Intr Enable P0.1 Intr Enable P0.0 Intr Enable
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Figure 9-7. Port 0 Interrupt Enable
Bit #
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
P1.7 Intr Enable P1.6 Intr Enable P1.5 Intr Enable P1.4 Intr Enable P1.3 Intr Enabl P1.2 Intr Enable P1.1 Intr Enable P1.0 Intr Enable
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Figure 9-8. Port 1 Interrupt Enable
Port 2 Interrupt Enable
Bit #
ADDRESS 0x06
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
P2.7 Intr Enable P2.6 Intr Enable P2.5 Intr Enable P2.4 Intr Enable P2.3 Intr Enable P2.2 Intr Enable P2.1 Intr Enable P2.0 Intr Enable
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Figure 9-9. Port 2 Interrupt Enable
Port 3 Interrupt Enable
Bit #
ADDRESS 0x07
7
6
5
4
3
2
1
0
Bit Name
Reserved
(Set to 0)
P3.6 Intr Enable P3.5 Intr Enable P3.4 Intr Enable P3.3 Intr Enable P3.2 Intr Enable P3.1 Intr Enable P3.0 Intr Enable
Read/Write
Reset
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Figure 9-10. Port 3 Interrupt Enable
10.0
DAC Port
The CY7C64113C features a programmable current sink 4 bit port which is also known as a DAC port. Each of these port I/O
pins have a programmable current sink. Writing a ‘1’ to a DAC I/O pin disables the output current sink (Isink DAC) and drives the
I/O pin HIGH through an integrated 14-kΩ resistor. When a ‘0’ is written to a DAC I/O pin, the Isink DAC is enabled and the pull-
up resistor is disabled. This causes the I
the DAC port pin.
sink
Document #: 38-08001 Rev. *B
Page 21 of 51
CY7C64013C
CY7C64113C
V
CC
Q1
Data
Out
Latch
Internal
Data Bus
Suspend
(Bit 3 of Register 0xFF)
14 kΩ
DAC Write
DAC
I/O Pin
4 bits
Isink
Register
Isink
DAC
Internal
Buffer
DAC Read
Interrupt
Enable
to Interrupt
Controller
Interrupt
Polarity
Figure 10-1. Block Diagram of a DAC Pin
The amount of sink current for the DAC I/O pin is programmable over 16 values based on the contents of the DAC Isink Register
for that output pin. DAC[1:0] are high-current outputs that are programmable from 3.2 mA to 16 mA (typical). DAC[7:2] are low-
current outputs, programmable from 0.2 mA to 1.0 mA (typical).
When the suspend bit in Processor Status and Control Register (see Figure 15-1) is set, the Isink DAC block of the DAC circuitry
is disabled. Special care should be taken when the CY7C64x13C device is placed in the suspend mode. The DAC Port Data
Register (see Figure 10-2) should normally be loaded with all ‘1’s (0xFF) before setting the suspend bit. If any of the DAC bits
are set to ‘0’ when the device is suspended, that DAC input will float. The floating pin could result in excessive current consumption
by the device, unless an external load places the pin in a deterministic state.
DAC Port Data
Bit #
ADDRESS 0x30
7
DAC[7]
R/W
1
6
Reserved
R/W
5
Reserved
R/W
4
Reserved
R/W
3
Reserved
R/W
2
DAC[2]
R/W
1
1
DAC[1]
R/W
1
0
Bit Name
Read/Write
Reset
DAC[0]
R/W
1
1
1
1
1
Figure 10-2. DAC Port Data
Bit [1..0]: High Current Output 3.2 mA to 16 mA typical
1= I/O pin is an output pulled HGH through the 14-kΩ resistor. 0 = I/O pin is an input with an internal 14-kΩ pull-up resistor
Bit [3..2]: Low Current Output 0.2 mA to 1 mA typical
1= I/O pin is an output pulled HGH through the 14-kΩ resistor. 0 = I/O pin is an input with an internal 14-kΩ pull-up resistor
10.1
DAC Isink Registers
Each DAC I/O pin has an associated DAC Isink register to program the output sink current when the output is driven LOW. The
first Isink register (0x38) controls the current for DAC[0], the second (0x39) for DAC[1], and so on until the Isink register at 0x3F
controls the current to DAC[7].
DAC Sink Register
Bit #
ADDRESS 0x38 -0x3F
7
6
5
4
3
Isink[3]
W
2
Isink[2]
W
1
Isink[1]
W
0
Bit Name
Read/Write
Reset
Reserved
Reserved
Reserved
Reserved
Isink[0]
W
0
-
-
-
-
0
0
0
Figure 10-3. DAC Sink Register
Document #: 38-08001 Rev. *B
Page 22 of 51
CY7C64013C
CY7C64113C
Bit [4..0]: Isink [x] (x= 0..4)
Writing all ‘0’s to the Isink register causes 1/5 of the max current to flow through the DAC I/O pin. Writing all ‘1’s to the
Isink register provides the maximum current flow through the pin. The other 14 states of the DAC sink current are evenly
spaced between these two values.
Bit [7..5]: Reserved
10.2 DAC Port Interrupts
A DAC port interrupt can be enabled/disabled for each pin individually. The DAC Port Interrupt Enable register provides this
feature with an interrupt enable bit for each DAC I/O pin.All of the DAC Port Interrupt Enable register bits are cleared to ‘0’ during
a reset. All DAC pins share a common interrupt, as explained in Section 16.6.
DAC Port Interrupt
Bit #
ADDRESS 0x31
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
Enable Bit 7
Reserved
Reserved
Reserved
Reserved
Enable Bit 2
Enable Bit 1
Enable Bit 0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Figure 10-4. DAC Port Interrupt Enable
Bit [7..0]: Enable bit x (x= 0..2, 7)
1= Enables interrupts from the corresponding bit position; 0= Disables interrupts from the corresponding bit position
As an additional benefit, the interrupt polarity for each DAC pin is programmable with the DAC Port Interrupt Polarity register.
Writing a ‘0’ to a bit selects negative polarity (falling edge) that causes an interrupt (if enabled) if a falling edge transition occurs
on the corresponding input pin. Writing a ‘1’ to a bit in this register selects positive polarity (rising edge) that causes an interrupt
(if enabled) if a rising edge transition occurs on the corresponding input pin. All of the DAC Port Interrupt Polarity register bits are
cleared during a reset.
DAC Port Interrupt Polarity
ADDRESS 0x32
Bit #
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
Enable Bit 7
Reserved
Reserved
Reserved
Reserved
Enable Bit 2
Enable Bit 1
Enable Bit 0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Figure 10-5. DAC Port Interrupt Polarity
Bit [7..0]: Enable bit x (x= 0..2, 7)
1= Selects positive polarity (rising edge) that causes an interrupt (if enabled);
0= Selects negative polarity (falling edge) that causes an interrupt (if enabled)
11.0
12-Bit Free-Running Timer
The 12-bit timer provides two interrupts (128-µs and 1.024-ms) and allows the firmware to directly time events that are up to 4
ms in duration. The lower 8 bits of the timer can be read directly by the firmware. Reading the lower 8 bits latches the upper 4
bits into a temporary register. When the firmware reads the upper 4 bits of the timer, it is accessing the count stored in the
temporary register. The effect of this logic is to ensure a stable 12-bit timer value can be read, even when the two reads are
separated in time.
Timer LSB
Bit #
ADDRESS 0x24
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
Timer Bit 7
Timer Bit 6
Timer Bit 5
Timer Bit 4
Timer Bit 3
Timer Bit 2
Timer Bit 1
Timer Bit 0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
R
0
Figure 11-1. Timer LSB Register
Bit [7:0]: Timer lower 8 bits
Document #: 38-08001 Rev. *B
Page 23 of 51
CY7C64013C
CY7C64113C
Timer MSB
Bit #
ADDRESS 0x25
7
6
5
4
3
2
1
0
Bit Name
Read/Write
Reset
Reserved
Reserved
Reserved
Reserved
Timer Bit 11
Timer Bit 10
Timer Bit 9
Timer Bit 8
-
-
-
-
R
0
R
0
R
0
R
0
0
0
0
0
Figure 11-2. Timer MSB Register
Bit [3:0]: Timer higher nibble
Bit [7:4]: Reserved
1.024-ms Interrupt
128- µs Interrupt
1-MHz Clock
11 10 9
8
7
6
5
4
3
2
1
0
L3 L2 L1 L0
D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
To Timer Register
8
Figure 11-3. Timer Block Diagram
12.0
I2C and HAPI Configuration Register
2
Internal hardware supports communication with external devices through two interfaces: a two-wire I C-compatible interface, and
2
a HAPI for 1, 2, or 3 byte transfers. The I C-compatible interface and HAPI functions, discussed in detail in Sections 13.0 and
14.0, share a common configuration register (see Figure 12-1). All bits of this register are cleared on reset.
I2C Configuration
ADDRESS 0x09
Bit #
7
6
5
4
3
2
1
0
2
Bit Name
I C Position
Reserved
LEMPTY
Polarity
DRDY
Latch
Data
HAPIPortWidth HAPIPortWidth
Polarity
Empty
Ready
Bit 1
R/W
0
Bit 0
R/W
0
Read/Write
Reset
R/W
0
-
R/W
0
R/W
0
R
0
R
0
0
2
Figure 12-1. HAPI/I C Configuration Register
2
2
2
Bits [7,1:0] of the HAPI/I C Configuration Register control the pin out configuration of the HAPI and I C-compatible interfaces.
Bits [5:2] are used in HAPI mode only, and are described in Section 14.0. Table 12-1 shows the HAPI port configurations, and
2
2
Table 12-2 shows I C pin location configuration options. These I C-compatible options exist due to pin limitations in certain
2
packages, and to allow simultaneous HAPI and I C-compatible operation.
HAPI operation is enabled whenever either HAPI Port Width Bit (Bit 1 or 0) is non-zero. This affects GPIO operation as described
2
Document #: 38-08001 Rev. *B
Page 24 of 51
CY7C64013C
CY7C64113C
Table 12-1. HAPI Port Configuration
Port Width (Bits[1:0])
HAPI Port Width
11
10
01
00
24 Bits: P3[7:0], P1[7:0], P0[7:0]
16 Bits: P1[7:0], P0[7:0]
8 Bits: P0[7:0]
No HAPI Interface
2
Table 12-2. I C Port Configuration
2
2
I C Position (Bit[7])
Port Width (Bit[1])
I C Position
2
X
0
1
1
0
0
I C on P2[1:0], 0:SCL, 1:SDA
2
I C on P1[1:0], 0:SCL, 1:SDA
2
I C on P2[1:0], 0:SCL, 1:SDA
13.0
I2C-compatible Controller
2
The I C-compatible block provides a versatile two-wire communication with external devices, supporting master, slave, and multi-
2
master modes of operation. The I C-compatible block functions by handling the low-level signaling in hardware, and issuing
interrupts as needed to allow firmware to take appropriate action during transactions. While waiting for firmware response, the
2
hardware keeps the I C-compatible bus idle if necessary.
2
The I C-compatible block generates an interrupt to the microcontroller at the end of each received or transmitted byte, when a
stop bit is detected by the slave when in receive mode, or when arbitration is lost. Details of the interrupt responses are given in
2
2
2
The I C-compatible interface consists of two registers, an I C Data Register (Figure 13-1) and an I C Status and Control Register
2
(Figure 13-2). The Data Register is implemented as separate read and write registers. Generally, the I C Status and Control
Register should only be monitored after the I C interrupt, as all bits are valid at that time. Polling this register at other times could
2
read misleading bit status if a transaction is underway.
2
2
The I C SCL clock is connected to bit 0 of GPIO port 1 or GPIO port 2, and the I C SDA data is connected to bit 1 of GPIO port
2
1 or GPIO port 2. Refer to Section 12.0 for the bit definitions and functionality of the HAPI/I C Configuration Register, which is
used to set the locations of the configurable I C-compatible pins. Once the I C-compatible functionality is enabled by setting bit
0 of the I C Status & Control Register, the two LSB bits ([1:0]) of the corresponding GPIO port are placed in Open Drain mode,
regardless of the settings of the GPIO Configuration Register.The electrical characteristics of the I C-compatible interface is the
2
2
2
2
same as that of GPIO ports 1 and 2. Note that the I (max) is 2 mA @ V = 2.0 V for ports 1 and 2.
OL
OL
2
2
All control of the I C clock and data lines is performed by the I C-compatible block.
I C Data
2
ADDRESS 0x29
Bit #
7
6
5
4
3
2
1
0
2
2
2
2
2
2
2
2
Bit Name
Read/Write
Reset
I C Data 7
I C Data 6
I C Data 5
I C Data 4
I C Data 3
I C Data 2
I C Data 1
I C Data 0
R/W
X
R/W
X
R/W
X
R/W
X
R/W
X
R/W
X
R/W
X
R/W
X
2
Figure 13-1. I C Data Register
2
Bits [7..0] : I C Data
2
Contains the 8 bit data on the I C Bus
2
I C Status and Control
Bit #
7
6
5
4
3
2
1
0
2
Bit Name
MSTR Mode
Continue/Busy
Xmit Mode
ACK
Addr
ARB
Lost/Restart
Received Stop
I C Enable
Read/Write
Reset
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
2
Figure 13-2. I C Status and Control Register
2
The I C Status and Control register bits are defined in Table 14-1, with a more detailed description following.
Document #: 38-08001 Rev. *B
Page 25 of 51
CY7C64013C
CY7C64113C
2
Table 13-1. I C Status and Control Register Bit Definitions
Bit
Name
Description
2
2
2
0
I C Enable
Received Stop
ARB Lost/Restart
Addr
When set to ‘1’, the I C-compatible function is enabled. When cleared, I C GPIO pins
operate normally.
2
1
2
3
4
Reads 1 only in slave receive mode, when I C Stop bit detected (unless firmware did not
ACK the last transaction).
Reads 1 to indicate master has lost arbitration. Reads 0 otherwise.
Write to 1 in master mode to perform a restart sequence (also set Continue bit).
Reads 1 during first byte after start/restart in slave mode, or if master loses arbitration.
Reads 0 otherwise. This bit should always be written as 0.
ACK
In receive mode, write 1 to generate ACK, 0 for no ACK.
In transmit mode, reads 1 if ACK was received, 0 if no ACK received.
5
6
Xmit Mode
Write to 1 for transmit mode, 0 for receive mode.
Continue/Busy
Write 1 to indicate ready for next transaction.
2
Reads 1 when I C-compatible block is busy with a transaction, 0 when transaction is
complete.
7
MSTR Mode
Write to 1 for master mode, 0 for slave mode. This bit is cleared if master loses arbitration.
Clearing from 1 to 0 generates Stop bit.
Bit 7 : MSTR Mode
2
Setting this bit to 1 causes the I C-compatible block to initiate a master mode transaction by sending a start bit and
transmitting the first data byte from the data register (this typically holds the target address and R/W bit). Subsequent bytes
are initiated by setting the Continue bit, as described below.
Clearing this bit (set to 0) causes the GPIO pins to operate normally
2
In master mode, the I C-compatible block generates the clock (SCK), and drives the data line as required depending on
2
transmit or receive state. The I C-compatible block performs any required arbitration and clock synchronization. IN the
event of a loss of arbitration, this MSTR bit is cleared, the ARB Lost bit is set, and an interrupt is generated by the
microcontroller. If the chip is the target of an external master that wins arbitration, then the interrupt is held off until the
transaction from the external master is completed.
2
When MSTR Mode is cleared from 1 to 0 by a firmware write, an I C Stop bit is generated.
Bit 6 : Continue / Busy
This bit is written by the firmware to indicate that the firmware is ready for the next byte transaction to begin. In other words,
the bit has responded to an interrupt request and has completed the required update or read of the data register. During a
2
read this bit indicates if the hardware is busy and is locking out additional writes to the I C Status and Control register. This
2
locking allows the hardware to complete certain operations that may require an extended period of time. Following an I C
2
interrupt, the I C-compatible block does not return to the Busy state until firmware sets the Continue bit. This allows the
firmware to make one control register write without the need to check the Busy bit.
Bit 5 : Xmit Mode
This bit is set by firmware to enter transmit mode and perform a data transmit in master or slave mode. Clearing this bit
2
sets the part in receive mode. Firmware generally determines the value of this bit from the R/W bit associated with the I C
address packet. The Xmit Mode bit state is ignored when initially writing the MSTR Mode or the Restart bits, as these cases
always cause transmit mode for the first byte.
Bit 4 : ACK
This bit is set or cleared by firmware during receive operation to indicate if the hardware should generate an ACK signal
2
2
on the I C-compatible bus. Writing a 1 to this bit generates an ACK (SDA LOW) on the I C-compatible bus at the ACK bit
time. During transmits (Xmit Mode = 1), this bit should be cleared.
Bit 3 : Addr
2
2
This bit is set by the I C-compatible block during the first byte of a slave receive transaction, after an I C start or restart.
The Addr bit is cleared when the firmware sets the Continue bit. This bit allows the firmware to recognize when the master
has lost arbitration, and in slave mode it allows the firmware to recognize that a start or restart has occurred.
Bit 2 : ARB Lost/Restart
This bit is valid as a status bit (ARB Lost) after master mode transactions. In master mode, set this bit (along with the
2
2
Continue and MSTR Mode bits) to perform an I C restart sequence. The I C target address for the restart must be written
Document #: 38-08001 Rev. *B
Page 26 of 51
CY7C64013C
CY7C64113C
to the data register before setting the Continue bit. To prevent false ARB Lost signals, the Restart bit is cleared by hardware
during the restart sequence.
Bit 1 : Receive Stop
This bit is set when the slave is in receive mode and detects a stop bit on the bus. The Receive Stop bit is not set if the
2
2
firmware terminates the I C transaction by not acknowledging the previous byte transmitted on the I C-compatible bus,
e.g. in receive mode if firmware sets the Continue bit and clears the ACK bit.
2
Bit 0 : I C Enable
2
2
Set this bit to override GPIO definition with I C-compatible function on the two I C-compatible pins. When this bit is cleared,
2
these pins are free to function as GPIOs. In I C-compatible mode, the two pins operate in open drain mode, independent
of the GPIO configuration setting.
14.0
Hardware Assisted Parallel Interface (HAPI)
The CY7C64x13C processor provides a hardware assisted parallel interface for bus widths of 8, 16, or 24 bits, to accommodate
2
data transfer with an external microcontroller or similar device. Control bits for selecting the byte width are in the HAPI/I C
Signals are provided on Port 2 to control the HAPI interface. Table 14-1 describes these signals and the HAPI control bits in the
2
HAPI/I C Configuration Register. Enabling HAPI causes the GPIO setting in the GPIO Configuration Register (0x08) to be
overridden. The Port 2 output pins are in CMOS output mode and Port 2 input pins are in input mode (open drain mode with Q3
Table 14-1. Port 2 Pin and HAPI Configuration Bit Definitions
Pin
P2[2]
Name
LatEmptyPin
DReadyPin
STB
Direction
Out
Description (Port 2 Pin)
Ready for more input data from external interface.
Output data ready for external interface.
Strobe signal for latching incoming data.
Output Enable, causes chip to output data.
Chip Select (Gates STB and OE).
P2[3]
P2[4]
P2[5]
P2[6]
Out
In
OE
In
CS
In
2
Bit
2
Name
R/W
R
Description (HAPI/I C Configuration Register)
Data Ready
Latch Empty
DRDY Polarity
Asserted after firmware writes data to Port 0, until OE driven LOW.
Asserted after firmware reads data from Port 0, until STB driven LOW.
3
R
4
R/W
Determines polarity of Data Ready bit and DReadyPin:
If 0, Data Ready is active LOW, DReadyPin is active HIGH.
If 1, Data Ready is active HIGH, DReadyPin is active LOW.
5
LEMPTY Polarity
R/W
Determines polarity of Latch Empty bit and LatEmptyPin:
If 0, Latch Empty is active LOW, LatEmptyPin is active HIGH.
If 1, Latch Empty is active HIGH, LatEmptyPin is active LOW.
HAPI Read by External Device from CY7C64x13C:
In this case (see Figure 24-3), firmware writes data to the GPIO ports. If 16-bit or 24-bit transfers are being made, Port 0 should
be written last, since writes to Port 0 asserts the Data Ready bit and the DReady Pin to signal the external device that data is
available.
The external device then drives the OE and CS pins active (LOW), which causes the HAPI data to be output on the port pins.
When OE is returned HIGH (inactive), the HAPI/GPIO interrupt is generated. At that point, firmware can reload the HAPI latches
for the next output, again writing Port 0 last.
The Data Ready bit reads the opposite state from the external DReadyPin on pin P2[3]. If the DRDY Polarity bit is 0, DReadyPin
is active HIGH, and the Data Ready bit is active LOW.
HAPI Write by External Device to CY7C64x13C:
In this case (see Figure 24-4), the external device drives the STB and CS pins active (LOW) when it drives new data onto the
port pins. When this happens, the internal latches become full, which causes the Latch Empty bit to be deasserted. When STB
is returned HIGH (inactive), the HAPI/GPIO interrupt is generated. Firmware then reads the parallel ports to empty the HAPI
latches. If 16-bit or 24-bit transfers are being made, Port 0 should be read last because reads from Port 0 assert the Latch Empty
bit and the LatEmptyPin to signal the external device for more data.
The Latch Empty bit reads the opposite state from the external LatEmptyPin on pin P2[2]. If the LEMPTY Polarity bit is 0,
LatEmptyPin is active HIGH, and the Latch Empty bit is active LOW.
Document #: 38-08001 Rev. *B
Page 27 of 51
CY7C64013C
CY7C64113C
15.0
Processor Status and Control Register
Processor Status and Control
ADDRESS 0xFF
Bit #
7
6
5
4
3
2
1
0
Bit Name
IRQ
Pending
Watchdog
Reset
USB Bus Reset
Interrupt
Power-On
Reset
Suspend
Interrupt
Enable Sense
Reserved
Run
Read/Write
Reset
R
0
R/W
0
R/W
0
R/W
1
R/W
0
R
0
R/W
0
R/W
1
Figure 15-1. Processor Status and Control Register
Bit 0: Run
This bit is manipulated by the HALT instruction. When Halt is executed, all the bits of the Processor Status and Control
Register are cleared to 0. Since the run bit is cleared, the processor stops at the end of the current instruction. The processor
remains halted until an appropriate reset occurs (power-on or Watchdog). This bit should normally be written as a ‘1.’
Bit 1: Reserved
Bit 1 is reserved and must be written as a zero.
Bit 2: Interrupt Enable Sense
This bit indicates whether interrupts are enabled or disabled. Firmware has no direct control over this bit as writing a zero
or one to this bit position has no effect on interrupts. A ‘0’ indicates that interrupts are masked off and a ‘1’ indicates that
the interrupts are enabled. This bit is further gated with the bit settings of the Global Interrupt Enable Register (Figure 16-
1) and USB End Point Interrupt Enable Register (Figure 16-2). Instructions DI, EI, and RETI manipulate the state of this bit.
Bit 3: Suspend
Writing a ‘1’ to the Suspend bit halts the processor and cause the microcontroller to enter the suspend mode that signifi-
cantly reduces power consumption. A pending, enabled interrupt or USB bus activity causes the device to come out of
suspend. After coming out of suspend, the device resumes firmware execution at the instruction following the IOWR which
put the part into suspend. An IOWR attempting to put the part into suspend is ignored if USB bus activity is present. See
Bit 4: Power-On Reset
The Power-On Reset is set to ‘1’ during a power-on reset. The firmware can check bits 4 and 6 in the reset handler to
determine whether a reset was caused by a power-on condition or a Watchdog timeout. A POR event may be followed by
a Watchdog reset before firmware begins executing, as explained below.
Bit 5: USB Bus Reset Interrupt
The USB Bus Reset Interrupt bit is set when the USB Bus Reset is detected on receiving a USB Bus Reset signal on the
upstream port. The USB Bus Reset signal is a single-ended zero (SE0) that lasts from 12 to 16 µs. An SE0 is defined as
the condition in which both the D+ line and the D– line are LOW at the same time.
Bit 6: Watchdog Reset
The Watchdog Reset is set during a reset initiated by the Watchdog Timer. This indicates the Watchdog Timer went for
more than t
(8 ms minimum) between Watchdog clears. This can occur with a POR event, as noted below.
WATCH
Bit 7: IRQ Pending
The IRQ pending, when set, indicates that one or more of the interrupts has been recognized as active. An interrupt remains
pending until its interrupt enable bit is set (Figure 16-1, Figure 16-2) and interrupts are globally enabled. At that point, the
internal interrupt handling sequence clears this bit until another interrupt is detected as pending.
During power-up, the Processor Status and Control Register is set to 00010001, which indicates a POR (bit 4 set) has occurred
and no interrupts are pending (bit 7 clear). During the 96 ms suspend at start-up (explained in Section 7.1), a Watchdog Reset
also occurs unless this suspend is aborted by an upstream SE0 before 8 ms. If a WDR occurs during the power-up suspend
interval, firmware reads 01010001 from the Status and Control Register after power-up. Normally, the POR bit should be cleared
so a subsequent WDR can be clearly identified. If an upstream bus reset is received before firmware examines this register, the
Bus Reset bit may also be set.
During a Watchdog Reset, the Processor Status and Control Register(Figure 15-1) is set to 01XX0001b, which indicates a
Watchdog Reset (bit 6 set) has occurred and no interrupts are pending (bit 7 clear). The Watchdog Reset does not effect the
state of the POR and the Bus Reset Interrupt bits.
Document #: 38-08001 Rev. *B
Page 28 of 51
CY7C64013C
CY7C64113C
16.0
Interrupts
2
Interrupts are generated by the GPIO/DAC pins, the internal timers, I C-compatible interface or HAPI operation, or on various
USB traffic conditions. All interrupts are maskable by the Global Interrupt Enable Register and the USB End Point Interrupt Enable
Register. Writing a ‘1’ to a bit position enables the interrupt associated with that bit position.
Global Interrupt Enable Register
ADDRESS 0X20
Bit #
7
6
5
4
3
2
1
0
2
Bit Name
Reserved
I C Interrupt
Enable
GPIO Interrupt
Enable
DAC Interrupt
enable
Reserved
1.024-ms
128-µsInterrupt USB Bus RST
Interrupt Enable
Enable
R/W
0
Interrupt Enable
Read/Write
Reset
-
-
R/W
0
R/W
0
-
R/W
0
R/W
0
R/W
0
X
Figure 16-1. Global Interrupt Enable Register
Bit 0 : USB Bus RST Interrupt Enable
1= Enable Interrupt on a USB Bus Reset; 0 = Disable interrupt on a USB Bus Reset (Refer to section 16.3)
Bit 1 :128-µs Interrupt Enable
1 = Enable Timer interrupt every 128 µs; 0 = Disable Timer Interrupt for every 128 µs.
Bit 2 : 1.024-ms Interrupt Enable
1= Enable Timer interrupt every 1.024 ms; 0 = Disable Timer Interrupt every 1.024 ms.
Bit 3 : Reserved
Bit 4 : DAC Interrupt Enable
1 = Enable DAC Interrupt; 0 = Disable DAC interrupt
Bit 5 : GPIO Interrupt Enable
1 = Enable Interrupt on falling/rising edge on any GPIO; 0 = Disable Interrupt on falling/rising edge on any GPIO (Refer to
section 14.7, 9.1 and 9.2.)
2
Bit 6 : I C Interrupt Enable
1= Enable Interrupt on I2C related activity; 0 = Disable I2C related activity interrupt. (Refer to section 16.8).
Bit 7 : Reserved
USB Endpoint Interrupt Enable
ADDRESS 0X21
Bit #
7
6
5
4
3
2
1
0
Bit Name
Reserved
Reserved
Reserved
EPB1 Interrupt
Enable
EPB0 Interrupt EPA2 Interrupt
EPA1 Interrupt EPA0 Interrupt
Enable
R/W
0
Enable
R/W
0
Enable
R/W
0
Enable
R/W
0
Read/Write
Reset
-
-
-
-
-
-
R/W
0
Figure 16-2. USB Endpoint Interrupt Enable Register
Bit 0: EPA0 Interrupt Enable
1= Enable Interrupt on data activity through endpoint A0; 0= Disable Interrupt on data activity through endpoint A0
Bit 1: EPA1 Interrupt Enable
1= Enable Interrupt on data activity through endpoint A1; 0= Disable Interrupt on data activity through endpoint A1
Bit 2: EPA2 Interrupt Enable
1= Enable Interrupt on data activity through endpoint A2; 0= Disable Interrupt on data activity through endpoint A2.
Bit 3: EPB0 Interrupt Enable
1= Enable Interrupt on data activity through endpoint B0; 0= Disable Interrupt on data activity through endpoint B0
Bit 4: EPB1 Interrupt Enable
1= Enable Interrupt on data activity through endpoint B1; 0= Disable Interrupt on data activity through endpoint B1
Bit [7..5] : Reserved
During a reset, the contents the Global Interrupt Enable Register and USB End Point Interrupt Enable Register are cleared,
effectively, disabling all interrupts
Document #: 38-08001 Rev. *B
Page 29 of 51
CY7C64013C
CY7C64113C
The interrupt controller contains a separate flip-flop for each interrupt. See Figure 16-3 for the logic block diagram of the interrupt
controller. When an interrupt is generated, it is first registered as a pending interrupt. It stays pending until it is serviced or a reset
occurs. A pending interrupt only generates an interrupt request if it is enabled by the corresponding bit in the interrupt enable
registers. The highest priority interrupt request is serviced following the completion of the currently executing instruction.
When servicing an interrupt, the hardware does the following
1. Disables all interrupts by clearing the Global Interrupt Enable bit in the CPU (the state of this bit can be read at Bit 2 of the
2. Clears the flip-flop of the current interrupt.
3. Generates an automatic CALL instruction to the ROM address associated with the interrupt being serviced (i.e., the Interrupt
Vector, see Section 16.1).
The instruction in the interrupt table is typically a JMP instruction to the address of the Interrupt Service Routine (ISR). The user
can re-enable interrupts in the interrupt service routine by executing an EI instruction. Interrupts can be nested to a level limited
only by the available stack space.
The Program Counter value as well as the Carry and Zero flags (CF, ZF) are stored onto the Program Stack by the automatic
CALL instruction generated as part of the interrupt acknowledge process. The user firmware is responsible for ensuring that the
processor state is preserved and restored during an interrupt. The PUSH A instruction should typically be used as the first
command in the ISR to save the accumulator value and the POP A instruction should be used to restore the accumulator value
just before the RETI instruction. The program counter CF and ZF are restored and interrupts are enabled when the RETI
instruction is executed.
The DI and EI instructions can be used to disable and enable interrupts, respectively. These instructions affect only the Global
Interrupt Enable bit of the CPU. If desired, EI can be used to re-enable interrupts while inside an ISR, instead of waiting for the
RETI that exists the ISR. While the global interrupt enable bit is cleared, the presence of a pending interrupt can be detected by
examining the IRQ Sense bit (Bit 7 in the Processor Status and Control Register).
16.1
Interrupt Vectors
The Interrupt Vectors supported by the USB Controller are listed in Table 16-1. The lowest-numbered interrupt (USB Bus Reset
interrupt) has the highest priority, and the highest-numbered interrupt (I C interrupt) has the lowest priority.
USB Reset Clear
Interrupt
Vector
To CPU
CLR
USB Reset IRQ
128-µs CLR
128-µs IRQ
1-ms CLR
1-ms IRQ
1
D
Q
Enable [0]
(Reg 0x20)
CPU
USB Reset Int
IRQ Sense
IRQ
CLK
IRQout
AddrA EP0 CLR
AddrA EP0 IRQ
AddrA EP1 CLR
AddrA EP1 IRQ
AddrA EP2 CLR
AddrA EP2 IRQ
CLR
Q
1
D
Global
Interrupt
Enable
Bit
Int Enable
Sense
Enable [2]
(Reg 0x21)
AddrB EP0 CLR
AddrB EP0 IRQ
AddrA ENP2 Int
CLK
AddrB EP1 CLR
AddrB EP1 IRQ
Controlled by DI, EI, and
RETI Instructions
CLR
Hub CLR
Hub IRQ
Interrupt
Acknowledge
DAC CLR
DAC IRQ
GPIO CLR
GPIO IRQ
I2C CLR
CLR
I2C IRQ
Q
1
Enable [6]
(Reg 0x20)
D
Interrupt Priority Encoder
I2C Int
CLK
Figure 16-3. Interrupt Controller Function Diagram
Although Reset is not an interrupt, the first instruction executed after a reset is at PROM address 0x0000h—which corresponds
to the first entry in the Interrupt Vector Table. Because the JMP instruction is two bytes long, the interrupt vectors occupy two bytes.
Document #: 38-08001 Rev. *B
Page 30 of 51
CY7C64013C
CY7C64113C
Table 16-1. Interrupt Vector Assignments
Interrupt Vector Number
ROM Address
0x0000
0x0002
0x0004
0x0006
0x0008
0x000A
0x000C
0x000E
0x0010
0x0012
0x0014
0x0016
0x0018
Function
Not Applicable
Execution after Reset begins here
USB Bus Reset interrupt
128- µs timer interrupt
1
2
3
1.024-ms timer interrupt
4
USB Address A Endpoint 0 interrupt
USB Address A Endpoint 1 interrupt
USB Address A Endpoint 2 interrupt
USB Address A Endpoint 3 interrupt
USB Address A Endpoint 4 interrupt
Reserved
5
6
7
8
9
10
11
12
DAC interrupt
GPIO interrupt
2
I C interrupt
16.2
Interrupt Latency
Interrupt latency can be calculated from the following equation:
Interrupt latency = (Number of clock cycles remaining in the current instruction) + (10 clock cycles for the CALL instruction) +
(5 clock cycles for the JMP instruction)
For example, if a 5 clock cycle instruction such as JC is being executed when an interrupt occurs, the first instruction of the
Interrupt Service Routine executes a minimum of 16 clocks (1+10+5) or a maximum of 20 clocks (5+10+5) after the interrupt is
issued. For a 12-MHz internal clock (6-MHz crystal), 20 clock periods is 20 / 12 MHz = 1.667 µs.
16.3
USB Bus Reset Interrupt
The USB Controller recognizes a USB Reset when a Single Ended Zero (SE0) condition persists on the upstream USB port for
12–16 µs (the Reset may be recognized for an SE0 as short as 12 µs, but is always recognized for an SE0 longer than 16 µs).
SE0 is defined as the condition in which both the D+ line and the D– line are LOW. Bit 5 of the Status and Control Register is set
to record this event. The interrupt is asserted at the end of the Bus Reset. If the USB reset occurs during the start-up delay
following a POR, the delay is aborted as described in Section 7.1. The USB Bus Reset Interrupt is generated when the SE0 state
is deasserted.
A USB Bus Reset clears the following registers:
SIE Section:USB Device Address Registers (0x10, 0x40)
16.4
Timer Interrupt
There are two periodic timer interrupts: the 128- µs interrupt and the 1.024-ms interrupt. The user should disable both timer
interrupts before going into the suspend mode to avoid possible conflicts between servicing the timer interrupts first or the suspend
request first.
16.5
USB Endpoint Interrupts
There are five USB endpoint interrupts, one per endpoint. A USB endpoint interrupt is generated after the USB host writes to a
USB endpoint FIFO or after the USB controller sends a packet to the USB host. The interrupt is generated on the last packet of
the transaction (e.g., on the host’s ACK during an IN, or on the device ACK during on OUT). If no ACK is received during an IN
transaction, no interrupt is generated.
16.6
DAC Interrupt
Each DAC I/O pin can generate an interrupt, if enabled. The interrupt polarity for each DAC I/O pin is programmable. A positive
polarity is a rising edge input while a negative polarity is a falling edge input. All of the DAC pins share a single interrupt vector,
which means the firmware needs to read the DAC port to determine which pin or pins caused an interrupt.
If one DAC pin has triggered an interrupt, no other DAC pins can cause a DAC interrupt until that pin has returned to its inactive
(non-trigger) state or the corresponding interrupt enable bit is cleared. The USB Controller does not assign interrupt priority to
different DAC pins and the DAC Interrupt Enable Register is not cleared during the interrupt acknowledge process.
Document #: 38-08001 Rev. *B
Page 31 of 51
CY7C64013C
CY7C64113C
16.7
GPIO/HAPI Interrupt
Each of the GPIO pins can generate an interrupt, if enabled. The interrupt polarity can be programmed for each GPIO port as
part of the GPIO configuration. All of the GPIO pins share a single interrupt vector, which means the firmware needs to read the
GPIO ports with enabled interrupts to determine which pin or pins caused an interrupt. A block diagram of the GPIO interrupt
logic is shown in Figure 16-4. Refer to Sections 9.1 and 9.2 for more information of setting GPIO interrupt polarity and enabling
individual GPIO interrupts.
If one port pin has triggered an interrupt, no other port pins can cause a GPIO interrupt until that port pin has returned to its inactive
(non-trigger) state or its corresponding port interrupt enable bit is cleared. The USB Controller does not assign interrupt priority
to different port pins and the Port Interrupt Enable Registers are not cleared during the interrupt acknowledge process.
Port
Configuration
GPIO Interrupt
Flip Flop
Register
OR Gate
(1 input per
GPIO pin)
IRQout
Interrupt
Priority
1
D
Q
M
U
X
Interrupt
Vector
Encoder
GPIO
Pin
CLR
Port Interrupt
Enable Register
1 = Enable
0 = Disable
IRA
Global
GPIO Interrupt
Enable
1 = Enable
0 = Disable
(Bit 5, Register 0x20)
Figure 16-4. GPIO Interrupt Structure
When HAPI is enabled, the HAPI logic takes over the interrupt vector and blocks any interrupt from the GPIO bits, including
ports/bits not being used by HAPI. Operation of the HAPI interrupt is independent of the GPIO specific bit interrupt enables, and
is enabled or disabled only by bit 5 of the Global Interrupt Enable Register (Figure 16-1) when HAPI is enabled. The settings of
the GPIO bit interrupt enables on ports/bits not used by HAPI still effect the CMOS mode operation of those ports/bits. The effect
of modifying the interrupt bits while the Port Config bits are set to “10” is shown in Table 9-1. The events that generate HAPI
interrupts are described in Section 14.0.
2
16.8
I C Interrupt
2
2
The I C interrupt occurs after various events on the I C-compatible bus to signal the need for firmware interaction. This generally
2
involves reading the I C Status and Control Register (Figure 13-2) to determine the cause of the interrupt, loading/reading the
I C Data Register as appropriate, and finally writing the Status and Control Register to initiate the subsequent transaction. The
2
2
interrupt indicates that status bits are stable and it is safe to read and write the I C registers. Refer to Section 13.0 for details on
2
the I C registers.
2
When enabled, the I C-compatible state machines generate interrupts on completion of the following conditions. The referenced
2
bits are in the I C Status and Control Register.
1. In slave receive mode, after the slave receives a byte of data: The Addr bit is set, if this is the first byte since a start or restart
signal was sent by the external master. Firmware must read or write the data register as necessary, then set the ACK, Xmit
MODE, and Continue/Busy bits appropriately for the next byte.
2. In slave receive mode, after a stop bit is detected: The Received Stop bit is set, if the stop bit follows a slave receive transaction
where the ACK bit was cleared to 0, no stop bit detection occurs.
3. In slave transmit mode, after the slave transmits a byte of data: The ACK bit indicates if the master that requested the byte
acknowledged the byte. If more bytes are to be sent, firmware writes the next byte into the Data Register and then sets the
Xmit MODE and Continue/Busy bits as required.
4. In master transmit mode, after the master sends a byte of data. Firmware should load the Data Register if necessary, and
set the Xmit MODE, MSTR MODE, and Continue/Busy bits appropriately. Clearing the MSTR MODE bit issues a stop signal
2
to the I C-compatible bus and return to the idle state.
Document #: 38-08001 Rev. *B
Page 32 of 51
CY7C64013C
CY7C64113C
5. In master receive mode, after the master receives a byte of data: Firmware should read the data and set the ACK and
Continue/Busy bits appropriately for the next byte. Clearing the MSTR MODE bit at the same time causes the master state
2
2
machine to issue a stop signal to the I C-compatible bus and leave the I C-compatible hardware in the idle state.
6. When the master loses arbitration: This condition clears the MSTR MODE bit and sets the ARB Lost/Restart bit immediately
2
and then waits for a stop signal on the I C-compatible bus to generate the interrupt.
The Continue/Busy bit is cleared by hardware prior to interrupt conditions 1 to 4. Once the Data Register has been read or written,
firmware should configure the other control bits and set the Continue/Busy bit for subsequent transactions. Following an interrupt
from master mode, firmware should perform only one write to the Status and Control Register that sets the Continue/Busy bit,
2
without checking the value of the Continue/Busy bit. The Busy bit may otherwise be active and I C register contents may be
2
changed by the hardware during the transaction, until the I C interrupt occurs.
17.0
USB Overview
The USB hardware consists of the logic for a full-speed USB Port. The full-speed serial interface engine (SIE) interfaces the
microcontroller to the USB bus. An external series resistor (R ) must be placed in series with the D+ and D– lines, as close to
ext
the corresponding pins as possible, to meet the USB driver requirements of the USB specifications.
17.1
USB Serial Interface Engine (SIE)
The SIE allows the CY7C64x13C microcontroller to communicate with the USB host. The SIE simplifies the interface between
the microcontroller and USB by incorporating hardware that handles the following USB bus activity independently of the micro-
controller:
• Bit stuffing/unstuffing
• Checksum generation/checking
• ACK/NAK/STALL
• Token type identification
• Address checking
Firmware is required to handle the following USB interface tasks:
• Coordinate enumeration by responding to SETUP packets
• Fill and empty the FIFOs
• Suspend/Resume coordination
• Verify and select DATA toggle values
17.2
USB Enumeration
The USB device is enumerated under firmware control. The following is a brief summary of the typical enumeration process of
the CY7C64x13C by the USB host. For a detailed description of the enumeration process, refer to the USB specification.
In this description, ‘Firmware’ refers to embedded firmware in the CY7C64x13C controller.
1. The host computer sends a SETUP packet followed by a DATA packet to USB address 0 requesting the Device descriptor.
2. Firmware decodes the request and retrieves its Device descriptor from the program memory tables.
3. The host computer performs a control read sequence and Firmware responds by sending the Device descriptor over the USB
bus, via the on-chip FIFOs.
4. After receiving the descriptor, the host sends a SETUP packet followed by a DATA packet to address 0 assigning a new USB
address to the device.
5. Firmware stores the new address in its USB Device Address Register after the no-data control sequence completes.
6. The host sends a request for the Device descriptor using the new USB address.
7. Firmware decodes the request and retrieves the Device descriptor from program memory tables.
8. The host performs a control read sequence and Firmware responds by sending its Device descriptor over the USB bus.
9. The host generates control reads from the device to request the Configuration and Report descriptors.
10.Once the device receives a Set Configuration request, its functions may now be used.
17.3
USB Upstream Port Status and Control
USB status and control is regulated by the USB Status and Control Register, as shown in Figure 17-1. All bits in the register are
cleared during reset.
Document #: 38-08001 Rev. *B
Page 33 of 51
CY7C64013C
CY7C64113C
USB Status and Control
Bit #
ADDRESS 0x1F
7
6
5
4
3
2
1
0
Bit Name
Endpoint Size
Endpoint Mode
D+ Upstream
D– Upstream
Bus Activity
Control Action
Bit 2
Control Action
Bit 1
Control Action
Bit 0
Read/Write
Reset
R/W
0
R/W
0
R
0
R
0
R/W
0
R/W
0
R/W
0
R/W
0
Figure 17-1. USB Status and Control Register
Bits[2..0] : Control Action
Set to control action as per Table 17-1.The three control bits allow the upstream port to be driven manually by firmware.
For normal USB operation, all of these bits must be cleared. Table 17-1 shows how the control bits affect the upstream port.
Table 17-1. Control Bit Definition for Upstream Port
Control Bits
000
Control Action
Not Forcing (SIE Controls Driver)
Force D+[0] HIGH, D–[0] LOW
Force D+[0] LOW, D–[0] HIGH
Force SE0; D+[0] LOW, D–[0] LOW
Force D+[0] LOW, D–[0] LOW
Force D+[0] HiZ, D–[0] LOW
Force D+[0] LOW, D–[0] HiZ
Force D+[0] HiZ, D–[0] HiZ
001
010
011
100
101
110
111
Bit 3 : Bus Activity
This is a “sticky” bit that indicates if any non-idle USB event has occurred on the upstream USB port. Firmware should
check and clear this bit periodically to detect any loss of bus activity. Writing a ‘0’ to the Bus Activity bit clears it, while writing
a ‘1’ preserves the current value. In other words, the firmware can clear the Bus Activity bit, but only the SIE can set it.
Bits 4 and 5 : D– Upstream and D+ Upstream
These bits give the state of each upstream port pin individually: 1 = HIGH, 0 = LOW.
Bit 6 : Endpoint Mode
This bit used to configure the number of USB endpoints. See Section 18.2 for a detailed description.
Bit 7 : Endpoint Size
This bit used to configure the number of USB endpoints. See Section 18.2 for a detailed description.
18.0
USB Serial Interface Engine Operation
USB Device Address A includes up to five endpoints: EPA0, EPA1, EPA2, EPA3, and EPA4. Endpoint (EPA0) allows the USB
host to recognize, set-up, and control the device. In particular, EPA0 is used to receive and transmit control (including set-up)
packets.
18.1
USB Device Address
The USB Controller provides one USB Device Address with five endpoints. The USB Device Address Register contents are
cleared during a reset, setting the USB device address to zero and marking this address as disabled. Figure 18-1 shows the
format of the USB Address Registers.
USB Device Address
Bit #
ADDRESSES 0x10
7
6
5
4
3
2
1
0
Bit Name
Device Address Device Address Device Address Device Address Device Address Device Address Device Address Device Address
Enable
R/W
0
Bit 6
R/W
0
Bit 5
R/W
0
Bit 4
R/W
0
Bit 3
R/W
0
Bit 2
R/W
0
Bit 1
R/W
0
Bit 0
R/W
0
Read/Write
Reset
Figure 18-1. USB Device Address Registers
Document #: 38-08001 Rev. *B
Page 34 of 51
CY7C64013C
CY7C64113C
Bits[6..0] :Device Address
Firmware writes this bits during the USB enumeration process to the non-zero address assigned by the USB host.
:Device Address Enable
Bit 7
Must be set by firmware before the SIE can respond to USB traffic to the Device Address.
Bit 7 (Device Address Enable) in the USB Device Address Register must be set by firmware before the SIE can respond to USB
traffic to this address. The Device Addresses in bits [6:0] are set by firmware during the USB enumeration process to the non-
zero address assigned by the USB host.
18.2
USB Device Endpoints
The CY7C64x13C controller supports one USB device address and five endpoints for communication with the host. The config-
uration of these endpoints, and associated FIFOs, is controlled by bits [7,6] of the USB Status and Control Register (0x1F). Bit 7
controls the size of the endpoints and bit 6 controls the number of endpoints. These configuration options are detailed in Table
18-1. The “unused” FIFO areas in the following table can be used by the firmware as additional user RAM space.
Table 18-1. Memory Allocation for Endpoints
USB Status And Control Register (0x1F) Bits [7, 6]
[0,0]
[1,0]
[0,1]
[1,1]
Start
Start
Start
Start
Label
unused
unused
EPA2
Address
Size
Label
unused
unused
EPA0
Address
Size
8
Label
EPA4
EPA3
EPA2
EPA1
EPA0
Address
Size
Label
EPA4
EPA3
EPA0
EPA1
EPA2
Address
Size
8
0xD8
0xE0
0xE8
0xF0
0xF8
8
8
8
8
8
0xA8
0xB0
0xB8
0xC0
0xE0
0xD8
0xE0
0xE8
0xF0
0xF8
8
8
8
8
8
0xB0
0xA8
0xB8
0xC0
0xE0
8
8
8
8
EPA1
EPA1
32
32
32
32
EPA0
EPA2
When the SIE writes data to a FIFO, the internal data bus is driven by the SIE; not the CPU. This causes a short delay in the
CPU operation. The delay is three clock cycles per byte. For example, an 8-byte data write by the SIE to the FIFO generates a
delay of 2 µs (3 cycles/byte * 83.33 ns/cycle * 8 bytes).
18.3
USB Control Endpoint Mode Register
All USB devices are required to have a Control Endpoint 0 (EPA0) that is used to initialize and control each USB address. Endpoint
0 provides access to the device configuration information and allows generic USB status and control accesses. Endpoint 0 is
bidirectional to both receive and transmit data. The other endpoints are unidirectional, but selectable by the user as IN or OUT
endpoints.
The endpoint mode register is cleared during reset. The endpoint zero EPA0 mode register uses the format shown in Figure 18-2.
USB Device Endpoint Zero Mode
ADDRESSES 0x12)
Bit #
7
6
5
4
3
2
1
0
Bit Name
Endpoint0SETUP
Received
Endpoint 0 IN Endpoint 0 OUT
ACK
Mode Bit 3
Mode Bit 2
Mode Bit 1
Mode Bit 0
Received
Received
Read/Write
Reset
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
Figure 18-2. USB Device Endpoint Zero Mode Registers
Bits[3..0] : Mode
These sets the mode which control how the control endpoint responds to traffic.
Bit 4 : ACK
This bit is set whenever the SIE engages in a transaction to the register’s endpoint that completes with an ACK packet.
Bit 5: Endpoint 0 OUT Received
1= Token received is an OUT token. 0= Token received is not an OUT token. This bit is set by the SIE to report the type of
token received by the corresponding device address is an OUT token. The bit must be cleared by firmware as part of the
USB processing.
Document #: 38-08001 Rev. *B
Page 35 of 51
CY7C64013C
CY7C64113C
Bit 6: Endpoint 0 IN Received
1= Token received is an IN token. 0= Token received is not an IN token. This bit is set by the SIE to report the type of token
received by the corresponding device address is an IN token. The bit must be cleared by firmware as part of the USB
processing.
Bit 7: Endpoint 0 SETUP Received
1= Token received is a SETUP token. 0= Token received is not a SETUP token. This bit is set ONLY by the SIE to report
the type of token received by the corresponding device address is a SETUP token. Any write to this bit by the CPU will
clear it (set it to 0). The bit is forced HIGH from the start of the data packet phase of the SETUP transaction until the start
of the ACK packet returned by the SIE. The CPU should not clear this bit during this interval, and subsequently, until the
CPU first does an IORD to this endpoint 0 mode register. The bit must be cleared by firmware as part of the USB processing.
Bits[6:0] of the endpoint 0 mode register are locked from CPU write operations whenever the SIE has updated one of these bits,
which the SIE does only at the end of the token phase of a transaction (SETUP... Data... ACK, OUT... Data... ACK, or IN... Data...
ACK). The CPU can unlock these bits by doing a subsequent read of this register. Only endpoint 0 mode registers are locked
when updated. The locking mechanism does not apply to the mode registers of other endpoints.
Because of these hardware locking features, firmware must perform an IORD after an IOWR to an endpoint 0 register. This verifies
that the contents have changed as desired, and that the SIE has not updated these values.
While the SETUP bit is set, the CPU cannot write to the endpoint zero FIFOs. This prevents firmware from overwriting an incoming
SETUP transaction before firmware has a chance to read the SETUP data. Refer to Table 18-1 for the appropriate endpoint zero
memory locations.
The Mode bits (bits [3:0]) control how the endpoint responds to USB bus traffic. The mode bit encoding is shown inTable 19-1.
18.4
USB Non-Control Endpoint Mode Registers
USB Non-Control Device Endpoint Mode
ADDRESSES 0x14, 0x16, 0x42, 0x44
Bit #
7
STALL
R/W
0
6
Reserved
R/W
5
Reserved
R/W
4
3
Mode Bit 3
R/W
2
Mode Bit 2
R/W
1
Mode Bit 1
R/W
0
Mode Bit 0
R/W
Bit Name
Read/Write
Reset
ACK
R/W
0
0
0
0
0
0
0
Figure 18-3. USB Non-Control Device Endpoint Mode Registers
Bits[3..0] : Mode
These sets the mode which control how the control endpoint responds to traffic. The mode bit encoding is shown in Table
Bit 4 : ACK
This bit is set whenever the SIE engages in a transaction to the register’s endpoint that completes with an ACK packet.
Bits[6..5] : Reserved
Must be written zero during register writes.
Bit 7 : STALL
If this STALL is set, the SIE stalls an OUT packet if the mode bits are set to ACK-IN, and the SIE stalls an IN packet if the
mode bits are set to ACK-OUT. For all other modes, the STALL bit must be a LOW.
18.5
USB Endpoint Counter Registers
There are five Endpoint Counter registers, with identical formats for both control and non-control endpoints. These registers
contain byte count information for USB transactions, as well as bits for data packet status. The format of these registers is shown
USB Endpoint Counter
Bit #
ADDRESSES 0x11, 0x13, 0x15, 0x41, 0x43
7
6
Data Valid
R/W
5
4
3
2
1
0
Bit Name
Read/Write
Reset
Data 0/1 Toggle
Byte Count Bit 5 Byte Count Bit 4 Byte Count Bit 3 Byte Count Bit 2 Byte Count Bit 1 Byte Count Bit 0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
R/W
0
0
Figure 18-4. USB Endpoint Counter Registers
Document #: 38-08001 Rev. *B
Page 36 of 51
CY7C64013C
CY7C64113C
Bits[5..0] : Byte Count
These counter bits indicate the number of data bytes in a transaction. For IN transactions, firmware loads the count with
the number of bytes to be transmitted to the host from the endpoint FIFO. Valid values are 0 to 32, inclusive. For OUT or
SETUP transactions, the count is updated by hardware to the number of data bytes received, plus 2 for the CRC bytes.
Valid values are 2 to 34, inclusive.
Bit 6 : Data Valid
This bit is set on receiving a proper CRC when the endpoint FIFO buffer is loaded with data during transactions. This bit is
used OUT and SETUP tokens only. If the CRC is not correct, the endpoint interrupt occurs, but Data Valid is cleared to a
zero.
Bit 7 : Data 0/1 Toggle
This bit selects the DATA packet’s toggle state: 0 for DATA0, 1 for DATA1. For IN transactions, firmware must set this bit to
the desired state. For OUT or SETUP transactions, the hardware sets this bit to the state of the received Data Toggle bit.
Whenever the count updates from a SETUP or OUT transaction on endpoint 0, the counter register locks and cannot be written
by the CPU. Reading the register unlocks it. This prevents firmware from overwriting a status update on incoming SETUP or OUT
transactions before firmware has a chance to read the data. Only endpoint 0 counter register is locked when updated. The locking
mechanism does not apply to the count registers of other endpoints.
18.6
Endpoint Mode/Count Registers Update and Locking Mechanism
The contents of the endpoint mode and counter registers are updated, based on the packet flow diagram in Figure 18-5. Two
time points, UPDATE and SETUP, are shown in the same figure. The following activities occur at each time point:
SETUP:
The SETUP bit of the endpoint 0 mode register is forced HIGH at this time. This bit is forced HIGH by the SIE until the end of the
data phase of a control write transfer. The SETUP bit can not be cleared by firmware during this time.
The affected mode and counter registers of endpoint 0 are locked from any CPU writes once they are updated. These registers
can be unlocked by a CPU read, only if the read operation occurs after the UPDATE. The firmware needs to perform a register
read as a part of the endpoint ISR processing to unlock the effected registers. The locking mechanism on mode and counter
registers ensures that the firmware recognizes the changes that the SIE might have made since the previous IO read of that
register.
UPDATE:
1. Endpoint Mode Register – All the bits are updated (except the SETUP bit of the endpoint 0 mode register).
2. Counter Registers – All bits are updated.
3. Interrupt – If an interrupt is to be generated as a result of the transaction, the interrupt flag for the corresponding endpoint is
set at this time. For details on what conditions are required to generate an endpoint interrupt, refer to Table 19-2.
4. The contents of the updated endpoint 0 mode and counter registers are locked, except the SETUP bit of the endpoint 0 mode
register which was locked earlier.
Document #: 38-08001 Rev. *B
Page 37 of 51
CY7C64013C
CY7C64113C
1. IN Token
Host To Device
Device To Host
Host To Device
D
A
T
A
S
Y
N
C
A
D
D
R
E
N
D
P
C
R
C
5
S
Y
N
C
C
R
C
S
A
Y
C
N
K
C
IN
Data
16
1/0
Hand
Shake
Packet
Token Packet
Data Packet
UPDATE
Host To Device
Device To Host
S
Y
N
C
A
D
D
R
E
N
D
P
C
R
C
5
S
Y
N
C
IN
NAK/STALL
D
E
V
I
C
E
Token Packet
Data Packet
H
O
S
T
UPDATE
2. OUT or SETUP Token without CRC error
Device To Host
Host To Device
Host To Device
O
U
T
D
A
S
Y
N
C
A
D
D
R
E
N
D
P
C
R
C
5
S
Y
N
C
C
R
C
S
Y
N
C
ACK,
NAK,
STAL
T
A
Data
/
Set
up
16
1/0
Hand
Shake
Packet
Token Packet
Data Packet
UPDATE
SETUP
3. OUT or SETUP Token with CRC error
Host To Device
Host To Device
O
U
T
D
A
T
A
1/0
S
Y
N
C
A
D
D
R
E
N
D
P
C
R
C
5
S
Y
N
C
C
R
C
Data
/
Set
up
16
Token Packet
Data Packet
UPDATE only if FIFO is
written
Figure 18-5. Token/Data Packet Flow Diagram
Document #: 38-08001 Rev. *B
Page 38 of 51
CY7C64013C
CY7C64113C
19.0
USB Mode Tables
Table 19-1. USB Register Mode Encoding
Mode Mode Bits SETUP
Disable
IN
OUT
Comments
0000
0001
ignore
accept
ignore
NAK
ignore Ignore all USB traffic to this endpoint
Nak In/Out
NAK Forced from Setup on Control endpoint, from modes other than
0000
Status Out Only
Stall In/Out
0010
0011
0100
0101
0110
0111
1000
accept
accept
accept
ignore
stall
stall
check For Control endpoints
stall For Control endpoints
ignore For Control endpoints
always For Isochronous endpoints
stall For Control Endpoints
Ignore In/Out
Isochronous Out
Status In Only
Isochronous In
Nak Out
ignore
ignore
accept TX 0 BYte
ignore TX Count ignore For Isochronous endpoints
ignore
ignore
NAK Is set by SIE on an ACK from mode 1001 (Ack Out)
Ack
1001
1001
ignore
ignore
ignore
ignore
ACK On issuance of an ACK this mode is changed by SIE to 1000
stall (NAK Out)
Out(STALL =0)
Ack
Out(STALL =1)
Nak Out - Status In
Ack Out - Status In
1010
1011
accept TX 0 BYte NAK Is set by SIE on an ACK from mode 1011 (Ack Out- Status In)
accept TX 0 BYte ACK On issuance of an ACK this mode is changed by SIE to 1010
(NAK Out - Status In)
Nak In
Ack
IN(STALL =0)
1100
ignore
NAK
ignore Is set by SIE on an ACK from mode 1101 (Ack In)
1101
1101
ignore TX Count ignore On issuance of an ACK this mode is changed by SIE to 1100
ignore
accept
stall
ignore (NAK In)
Ack
IN(STALL =1)
Nak In - Status Out
Ack In - Status Out
1110
1111
NAK
check Is set by SIE on an ACK from mode 1111 (Ack In - Status Out)
accept TX Count check On issuance of an ACK this mode is changed by SIE to 1110
(NAK In - Status Out)
Mode
This lists the mnemonic given to the different modes that can be set in the Endpoint Mode Register by writing to the lower nibble
(bits 0..3). The bit settings for different modes are covered in the column marked “Mode Bits”. The Status IN and Status OUT
represent the Status stage in the IN or OUT transfer involving the control endpoint.
Mode Bits
These column lists the encoding for different modes by setting Bits[3..0] of the Endpoint Mode register. This modes represents
how the SIE responds to different tokens sent by the host to an endpoint. For instance, if the mode bits are set to “0001” (NAK
IN/OUT), the SIE will respond with an
• ACK on receiving a SETUP token from the host
• NAK on receiving an OUT token from the host
• NAK on receiving an IN token from the host
Refer to section 13.0 for more information on the SIE functioning
SETUP, IN and OUT
These columns shows the SIE’s response to the host on receiving a SETUP, IN and OUT token depending on the mode set in
the Endpoint Mode Register.
A “Check” on the OUT token column, implies that on receiving an OUT token the SIE checks to see whether the OUT packet is
of zero length and has a Data Toggle (DTOG) set to ‘1.’ If the DTOG bit is set and the received OUT Packet has zero length, the
OUT is ACKed to complete the transaction. If either of this condition is not met the SIE will respond with a STALLL or just ignore
the transaction.
A “TX Count” entry in the IN column implies that the SIE transmit the number of bytes specified in the Byte Count (bits 3..0 of the
Endpoint Count Register) to the host in response to the IN token received.
A “TX0 Byte” entry in the IN column implies that the SIE transmit a zero length byte packet in response to the IN token received
from the host.
An “Ignore” in any of the columns means that the device will not send any handshake tokens (no ACK) to the host.
Document #: 38-08001 Rev. *B
Page 39 of 51
CY7C64013C
CY7C64113C
An “Accept” in any of the columns means that the device will respond with an ACK to a valid SETUP transaction tot he host.
Comments
Some Mode Bits are automatically changed by the SIE in response to certain USB transactions. For example, if the Mode Bits
[3:0] are set to '1111' which is ACK IN-Status OUT mode as shown in table 22-1, the SIE will change the endpoint Mode Bits [3:0]
to NAK IN-Status OUT mode (1110) after ACK’ing a valid status stage OUT token. The firmware needs to update the mode for
the SIE to respond appropriately. See Table 18-1 for more details on what modes will be changed by the SIE. A disabled endpoint
will remain disabled until changed by firmware, and all endpoints reset to the disabled mode (0000). Firmware normally enables
the endpoint mode after a SetConfiguration request.
Any SETUP packet to an enabled endpoint with mode set to accept SETUPs will be changed by the SIE to 0001 (NAKing INs
and OUTs). Any mode set to accept a SETUP will send an ACK handshake to a valid SETUP token.
The control endpoint has three status bits for identifying the token type received (SETUP, IN, or OUT), but the endpoint must be
placed in the correct mode to function as such. Non-Control endpoints should not be placed into modes that accept SETUPs.
Note that most modes that control transactions involving an ending ACK, are changed by the SIE to a corresponding mode which
NAKs subsequent packets following the ACK. Exceptions are modes 1010 and 1110.
Note: The SIE offers an “Ack out–Status in” mode and not an “Ack out–Nak in” mode. Therefore, if following the status stage of
a Control Write transfer a USB host were to immediately start the next transfer, the new Setup packet could override the data
payload of the data stage of the previous Control Write.
Properties of
Incoming Packets
Changes to the Internal Register made by the SIE on receiving an incoming packet
from the host
Interrupt
3
2
1
0
Token
count
buffer
dval
DTOG
DVAL
COUNT
Setup
In
Out
ACK
3
2
1
0
Response Int
Byte Count (bits 0..5, Figure 17-4)
Data Valid (bit 6, Figure 17-4)
Endpoint Mode
encoding
SIE’sResponse
to the Host
Received Token
(SETUP/IN/OUT)
Data0/1 (bit7 Figure 17-4)
PID Status Bits
(Bit[7..5], Figure 17-2)
Endpoint Mode bits
Changed by the SIE
The validity of the received data
The quality status of the DMA buffer
The number of received bytes
Acknowledge phase completed
Legend:
TX : transmit
RX : receive
UC : unchanged
TX0 :Transmit 0 length packet
available for Control endpoint only
x: don’t care
The response of the SIE can be summarized as follows:
1. The SIE will only respond to valid transactions, and will ignore non-valid ones.
2. The SIE will generate an interrupt when a valid transaction is completed or when the FIFO is corrupted. FIFO corruption occurs
during an OUT or SETUP transaction to a valid internal address, that ends with a non-valid CRC.
3. An incoming Data packet is valid if the count is < Endpoint Size + 2 (includes CRC) and passes all error checking;
4. An IN will be ignored by an OUT configured endpoint and visa versa.
5. The IN and OUT PID status is updated at the end of a transaction.
6. The SETUP PID status is updated at the beginning of the Data packet phase.
7. The entire Endpoint 0 mode register and the Count register are locked to CPU writes at the end of any transaction to that
endpoint in which an ACK is transferred. These registers are only unlocked by a CPU read of the register, which should be
done by the firmware only after the transaction is complete. This represents about a 1- µs window in which the CPU is locked
from register writes to these USB registers. Normally the firmware should perform a register read at the beginning of the
Endpoint ISRs to unlock and get the mode register information. The interlock on the Mode and Count registers ensures that
Document #: 38-08001 Rev. *B
Page 40 of 51
CY7C64013C
CY7C64113C
the firmware recognizes the changes that the SIE might have made during the previous transaction. Note that the setup bit of
the mode register is NOT locked. This means that before writing to the mode register, firmware must first read the register to
make sure that the setup bit is not set (which indicates a setup was received, while processing the current USB request). This
read will of course unlock the register. So care must be taken not to overwrite the register elsewhere.
Table 19-2. Details of Modes for Differing Traffic Conditions (see Table 19-1 for the decode legend)
SETUP (if accepting SETUPs)
Properties of Incoming Packet
Changes made by SIE to Internal Registers and Mode Bits
Mode Bits
token
Setup
Setup
Setup
count buffer
dval
valid
x
DTOG
DVAL
COUNT Setup
In
Out ACK
Mode Bits Response
ACK
Intr
yes
yes
yes
<= 10 data
updates
1
updates
1
1
1
UC UC
UC UC
UC UC
1
0
0
0
1
> 10
x
junk
junk
updates updates updates
updates updates
UC
UC
NoChange ignore
NoChange ignore
invalid
0
Properties of Incoming Packet
Changes made by SIE to Internal Registers and Mode Bits
Mode Bits
token
count buffer
dval
DTOG
DVAL
COUNT Setup
In
Out ACK
Mode Bits Response
Intr
DISABLED
0
0
0
0
x
x
UC
x
UC
UC
UC
UC
UC UC
UC
NoChange ignore
no
Nak In/Out
0
0
0
0
0
0
1
1
Out
In
x
x
UC
UC
x
x
UC
UC
UC
UC
UC
UC
UC
UC
UC
1
1
UC
UC
NoChange NAK
NoChange NAK
yes
yes
UC
Ignore In/Out
0
0
1
1
0
0
0
0
Out
In
x
x
UC
UC
x
x
UC
UC
UC
UC
UC
UC
UC
UC
UC UC
UC UC
UC
UC
NoChange ignore
NoChange ignore
no
no
Stall In/Out
0
0
0
0
1
1
1
1
Out
In
x
x
UC
UC
x
x
UC
UC
UC
UC
UC
UC
UC
UC
UC
1
1
UC
UC
NoChange Stall
NoChange Stall
yes
yes
UC
CONTROL WRITE
Properties of Incoming Packet
Mode Bits token count buffer
Normal Out/premature status In
Changes made by SIE to Internal Registers and Mode Bits
dval
DTOG
DVAL
COUNT Setup
In
Out ACK
Mode Bits Response
Intr
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
Out
Out
Out
In
<= 10 data
valid
updates
1
updates UC
UC
UC
UC
1
1
1
1
0
1
0
ACK
yes
yes
yes
yes
> 10
junk
junk
UC
x
updates updates updates UC
1
UC
UC
1
NoChange ignore
NoChange ignore
NoChange TX 0
x
x
invalid
x
updates
UC
0
updates UC
1
UC
UC
UC
UC
NAK Out/premature status In
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
Out
Out
Out
In
<= 10 UC
valid
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
1
UC
UC
UC
1
NoChange NAK
NoChange ignore
NoChange ignore
NoChange TX 0
yes
no
> 10
UC
UC
UC
x
UC UC
UC UC
x
x
invalid
x
no
1
UC
yes
Status In/extra Out
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
Out
Out
Out
In
<= 10 UC
valid
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
1
UC
UC
UC
1
0
0
1
1
Stall
yes
no
> 10
UC
UC
UC
x
UC UC
UC UC
NoChange ignore
NoChange ignore
NoChange TX 0
x
x
invalid
x
no
1
UC
yes
CONTROL READ
Properties of Incoming Packet
Mode Bits token count buffer
Normal In/premature status Out
Changes made by SIE to Internal Registers and Mode Bits
dval
DTOG
DVAL
COUNT Setup
In
Out ACK
Mode Bits Response
Intr
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Out
Out
Out
Out
Out
In
2
UC
UC
UC
UC
UC
UC
valid
valid
valid
x
1
1
updates UC
updates UC
updates UC
UC
UC
UC
1
1
1
1
NoChange ACK
yes
yes
yes
no
2
0
1
UC
UC
UC
UC
1
0
0
0
0
1
1
1
1
Stall
Stall
!=2
> 10
x
updates
UC
1
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC UC
UC UC
NoChange ignore
NoChange ignore
invalid
x
UC
no
x
UC
1
UC
1
1
1
0
ACK (back)
yes
Nak In/premature status Out
1
1
1
1
1
1
0
0
Out
Out
2
2
UC
UC
valid
valid
1
0
1
1
updates UC
updates UC
UC
UC
1
1
1
NoChange ACK
Stall
yes
yes
UC
0
0
1
1
Document #: 38-08001 Rev. *B
Page 41 of 51
CY7C64013C
CY7C64113C
Table 19-2. Details of Modes for Differing Traffic Conditions (see Table 19-1 for the decode legend) (continued)
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
Out
Out
Out
In
!=2
> 10
x
UC
UC
UC
UC
valid
updates
UC
1
updates UC
UC
1
UC
UC
UC
UC
0
0
1
1
Stall
yes
no
x
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC UC
UC UC
NoChange ignore
NoChange ignore
NoChange NAK
invalid
x
UC
no
x
UC
1
UC
yes
Status Out/extra In
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Out
Out
Out
Out
Out
In
2
UC
UC
UC
UC
UC
UC
valid
valid
valid
x
1
1
updates UC
updates UC
updates UC
UC
UC
UC
1
1
1
1
NoChange ACK
yes
yes
yes
no
2
0
1
UC
UC
UC
UC
UC
0
0
0
0
1
1
1
1
Stall
Stall
!=2
> 10
x
updates
UC
1
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC UC
NoChange ignore
NoChange ignore
invalid
x
UC
1
1
UC
UC
no
x
UC
0
0
1
1
Stall
yes
OUT ENDPOINT
Properties of Incoming Packet
Changes made by SIE to Internal Registers and Mode Bits
Mode Bits
token
count buffer
dval
DTOG
DVAL
COUNT Setup
In
Out ACK
Mode Bits Response
Intr
Normal Out/erroneous In
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
Out
Out
Out
In
<= 10 data
valid
updates
1
updates UC
UC UC
UC UC
UC UC
UC UC
1
1
0
0
0
ACK
yes
yes
yes
no
> 10
junk
junk
UC
x
updates updates updates UC
UC
UC
UC
NoChange ignore
NoChange ignore
NoChange ignore
x
x
invalid
x
updates
UC
0
updates UC
UC
UC
UC
UC
UC
(STALL = 0)
NoChange Stall
(STALL = 1)
1
0
0
1
In
x
UC
x
UC
UC
UC UC
UC
no
NAK Out/erroneous In
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Out
Out
Out
In
<= 10 UC
valid
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
UC
1
UC
UC
UC
UC
NoChange NAK
yes
no
> 10
UC
UC
UC
x
UC UC
UC UC
UC UC
NoChange ignore
NoChange ignore
NoChange ignore
x
x
invalid
x
no
no
Isochronous endpoint (Out)
0
0
1
1
0
0
1
1
Out
In
x
x
updates updates
updates updates updates UC
UC UC UC UC
UC
1
1
NoChange RX
yes
no
UC
x
UC UC
UC
NoChange ignore
IN ENDPOINT
Properties of Incoming Packet
Mode Bits token count buffer
Normal In/erroneous Out
Changes made by SIE to Internal Registers and Mode Bits
dval
DTOG
DVAL
COUNT Setup
In
Out ACK
Mode Bits Response
Intr
no
1
1
1
1
1
1
0
0
0
1
1
1
Out
Out
In
x
x
x
UC
UC
UC
x
x
x
UC
UC
UC
UC
UC
UC
UC
UC
UC UC
UC UC
UC
UC
1
NoChange ignore
(STALL = 0)
UC
UC
NoChange stall
no
(STALL = 1)
UC
UC
1
UC
1
1
0
0
ACK (back)
yes
NAK In/erroneous Out
1
1
1
1
0
0
0
0
Out
In
x
x
UC
UC
x
x
UC
UC
UC
UC
UC
UC
UC
UC
UC UC
UC
UC
UC
NoChange ignore
NoChange NAK
no
1
yes
Isochronous endpoint (In)
0
0
1
1
1
1
1
1
Out
In
x
x
UC
UC
x
x
UC
UC
UC
UC
UC
UC
UC
UC
UC UC
UC
UC
UC
NoChange ignore
NoChange TX
no
1
yes
Note:
3. STALL bit is bit 7 of the USB Non-Control Device Endpoint Mode registers. For more information, refer to Sec.
Document #: 38-08001 Rev. *B
Page 42 of 51
CY7C64013C
CY7C64113C
20.0
Register Summary
Read/Write/ Default/
Address RegisterName Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Both/-
Reset
0x00
0x01
0x02
0x03
0x04
Port 0 Data
P0.7
P1.7
P2.7
P3.7
P0.6
P1.6
P2.6
P3.6
P0.5
P1.5
P2.5
P3.5
P0.4
P1.4
P2.4
P3.4
P0.3
P1.3
P2.3
P3.3
P0.2
P1.2
P2.2
P3.2
P0.1
P1.1
P2.1
P3.1
P0.0
P1.0
P2.0
P3.0
BBBBBBBB
11111111
11111111
11111111
11111111
00000000
Port 1 Data
BBBBBBBB
Port 2 Data
BBBBBBBB
Port 3 Data
BBBBBBBB
Port 0 Interrupt Enable
P0.7 Intr
Enable
P0.6 Intr
Enable
P0.5 Intr
Enable
P0.4 Intr
Enable
P0.3 Intr
Enable
P0.2 Intr
Enable
P0.1 Intr
Enable
P0.0 Intr
Enable
WWWWWWWW
0x05
0x06
0x07
0x08
Port 1 Interrupt Enable
Port 2 Interrupt Enable
Port 3 Interrupt Enable
GPIO Configuration
2
P1.7 Intr
Enable
P1.6 Intr
Enable
P1.5 Intr
Enable
P1.4 Intr
Enable
Reserved
P1.2 Intr
Enable
P1.1 Intr
Enable
P1.0 Intr
Enable
WWWWWWWW
WWWWWWWW
WWWWWWWW
BBBBBBBB
00000000
00000000
00000000
00000000
P2.7 Intr
Enable
P2.6 Intr
Enable
P2.5 Intr
Enable
P2.4 Intr
Enable
P2.3 Intr
Enable
Reserved
Reserved
Port 1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
P3.1 Intr
Enable
P3.0 Intr
Enable
Port 3
Port 3
Port 2
Port 2
Port 1
Port 0
Port 0
Config Bit 1 Config Bit 0 Config Bit 1 Config Bit 0 Config Bit 1 Config Bit 0 Config Bit 1 Config Bit 0
2
2
0x09
0x10
HAPI/I C Configuration I C Position Reserved
Reserved
Reserved
Reserved
Reserved
I C Port
Reserved
BBBBBBBB
BBBBBBBB
00000000
00000000
Width
USB Device Address A
Device
Device
Device
Device
Device
Device
Device
Device
Address A Address A Address A Address A Address A Address A Address A Address A
Enable
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0x11
0x12
EP A0 Counter
Register
Data 0/1
Toggle
Data Valid Byte Count Byte Count Byte Count Byte Count Byte Count Byte Count
BBBBBBBB
BBBBBBBB
00000000
00000000
Bit 5
Bit 4
ACK
Bit 3
Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0
Bit 2
Bit 1
Bit 0
EP A0 Mode Register
Endpoint0 Endpoint0 Endpoint0
SETUP
Received
IN
OUT
Received
Received
0x13
EP A1 Counter
Register
Data 0/1
Toggle
Data Valid Byte Count Byte Count Byte Count Byte Count Byte Count Byte Count
BBBBBBBB
00000000
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0x14
0x15
EP A1 Mode Register
STALL
-
-
ACK
Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0
BBBBBBBB
BBBBBBBB
00000000
00000000
EP A2 Counter
Register
Data 0/1
Toggle
Data Valid Byte Count Byte Count Byte Count Byte Count Byte Count Byte Count
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0x16
0x1F
EP A2 Mode Register
STALL
-
-
ACK
Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0
BBBBBBBB
BBRRBBBB
00000000
-0xx0000
USB Status and Control Endpoint
Size
Endpoint
Mode
D+
Upstream
D–
Upstream
Bus Activity
Control
Bit 2
Control
Bit 1
Control
Bit 0
2
0x20
0x21
Global Interrupt Enable Reserved
I C
GPIO
Interrupt
Enable
Reserved
USB Hub
Interrupt
Enable
1.024-ms
Interrupt
Enable
128-µs
Interrupt
Enable
USB Bus
RESET
Interrupt
Enable
-BBBBBBB
---BBBBB
-0000000
---00000
Interrupt
Enable
Endpoint Interrupt
Enable
Reserved
Reserved
Reserved
EPB1
Interrupt
Enable
EPB0
Interrupt
Enable
EPA2
Interrupt
Enable
EPA1
Interrupt
Enable
EPA0
Interrupt
Enable
0x24
0x25
Timer (LSB)
Timer (MSB)
Timer Bit 7 Timer Bit 6 Timer Bit 5 Timer Bit 4 Timer Bit 3 Timer Bit 2 Timer Bit 1 Timer Bit 0
RRRRRRRR
----rrrr
00000000
----0000
Reserved
Reserved
Reserved
Reserved Timer Bit 11 Timer Bit 10 Time Bit 9 Timer Bit 8
0x26
0x28
WDT Clear
x
x6
x
x
x 3
x2
x
x
WWWWWWWW
BBBBBBBB
xxxxxxxx
2
2
I C Control and Status
MSTR
Mode
Continue/
Busy
Xmit
Mode
ACK
Addr
ARB Lost/
Restart
Received
Stop
I C
00000000
Enable
2
2
2
2
2
2
2
2
2
0x29
0x30
0x31
0x32
I C Data
I C Data 7 I C Data 6 I C Data 5 I C Data 4 I C Data 3 I C Data 2 I C Data 1 I C Data 0
Timer Bit 7 Timer Bit 6 Timer Bit 5 Timer Bit 4 Timer Bit 3 Timer Bit 2 Timer Bit 1 Timer Bit 0
BBBBBBBB
RRRRRRRR
----rrrr
XXXXXXXX
00000000
----0000
DAC Data
DAC Interrupt Enable)
DAC Interrupt Polarity
Reserved
Reserved
Reserved
Reserved Timer Bit 11 Timer Bit 10 Time Bit 9 Timer Bit 8
0x38- 0x3F DAS Isink
x
x6
x
x
x 3
x2
x
x
WWWWWWWW
BBBBBBBB
0x40
0x41
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
00000000
00000000
EP A3 Counter Register Data 0/1
Toggle
Data Valid Byte Count Byte Count Byte Count Byte Count Byte Count Byte Count
BBBBBBBB
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0x42
EP A3 Mode Register
Endpoint 0 Endpoint 0 Endpoint 0
ACK
Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0
BBBBBBBB
00000000
SETUP
IN
OUT
Received
Received
Received
0x43
0x44
EP A4 Counter Register Data 0/1
Toggle
Data Valid Byte Count Byte Count Byte Count Byte Count Byte Count Byte Count
BBBBBBBB
BBBBBBBB
00000000
00000000
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EP A4 Mode Register
STALL
-
-
ACK
Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0
Document #: 38-08001 Rev. *B
Page 43 of 51
CY7C64013C
CY7C64113C
Read/Write/ Default/
Address RegisterName Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Both/-
Reset
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
0x50
0x51
0x52
0xFF
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Suspend
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Run
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RBBBBRBB
00000000
00000000
00000000
00000000
--000000
00000000
00000000
00000000
00000000
00000000
00000000
00010001
Process Status &
Control
IRQ
Pending
Watchdog
Reset
USB Bus
Reset
Interrupt
Power-On
Reset
Interrupt
Enable
Sense
Note:
B: Read and Write
W: Write
R: Read
21.0
Sample Schematic
3.3V Regulator
Vref
2.2 µF
OUT
IN
2.2 µF
Vref
0V
1.5K
(R
)
UUP
USB-B
Vbus
D–
D+
GND
.01 µF
.01 µF
Vbus
22x2(R
)
ext
0V
0V
SHELL
D0–
D0+
4.7 nF
Optional
250VAC
XTALO
XTALI
10M
6.000 MHz
GND
GND
Vpp
0V
0V
Document #: 38-08001 Rev. *B
Page 44 of 51
CY7C64013C
CY7C64113C
22.0
Absolute Maximum Ratings
Storage Temperature ..........................................................................................................................................–65°C to +150°C
Ambient Temperature with Power Applied.................................................................................................................0°C to +70°C
Supply voltage on V relative to V ....................................................................................................................–0.5V to +7.0V
CC
SS
DC Input Voltage........................................................................................................................................... –0.5V to +V +0.5V
CC
DC Voltage Applied to Outputs in High Z State............................................................................................. –0.5V to +V +0.5V
CC
Power Dissipation ............................................................................................................................................................. 500 mW
Static Discharge Voltage ................................................................................................................................................... >2000V
Latch-up Current ............................................................................................................................................................ >200 mA
Max Output Sink Current into Port 0, 1, 2, 3, and DAC[1:0] Pins ...................................................................................... 60 mA
Max Output Sink Current into DAC[7:2] Pins...................................................................................................................... 10 mA
23.0
OSC
Electrical Characteristics
f
= 6 MHz; Operating Temperature = 0 to 70°C, V = 4.0V to 5.25V
CC
Parameter
Description
General
Conditions
Min.
Max.
Unit
V
V
Reference Voltage
Programming Voltage (disabled)
Operating Current
3.3V ±5%
3.15
–0.4
3.45
0.4
50
50
30
1
V
REF
V
pp
ICC
V
No GPIO source current
mA
µA
mA
µA
CC
ISB1
Supply Current—Suspend Mode
Operating Current
I
I
V
Note 5
ref
il
REF
Input Leakage Current
USB Interface
Any pin
V
V
V
Differential Input Sensitivity
| (D+)–(D–) |
0.2
0.8
0.8
V
V
di
Differential Input Common Mode Range
Single Ended Receiver Threshold
Transceiver Capacitance
2.5
2.0
20
cm
se
V
C
pF
µA
Ω
in
I
Hi-Z State Data Line Leakage
External USB Series Resistor
0 V < V < 3.3 V
–10
19
10
lo
in
R
R
In series with each USB pin
21
ext
External Upstream USB Pull-up Resistor 1.5 kΩ ±5%, D+ to V
1.425 1.575
kΩ
UUP
REG
Power On Reset
t
V
Ramp Rate
Linear ramp 0V to V
0
100
ms
vccs
CC
CC
USB Upstream
V
V
Z
Static Output High
15 kΩ ±5% to Gnd
2.8
28
3.6
0.3
44
V
V
Ω
UOH
Static Output Low
1.5 kΩ ±5% to V
UOL
REF
USB Driver Output Impedance
General Purpose I/O (GPIO)
Pull-up Resistance (typical 14 kΩ)
Input Threshold Voltage
Including R Resistor
O
ext
R
8.0
20%
2%
24.0
40%
8%
kΩ
up
ITH
H
V
V
V
All ports, LOW to HIGH edge
All ports, HIGH to LOW edge
V
V
CC
CC
Input Hysteresis Voltage
Port 0,1,2,3 Output Low Voltage
I
I
= 3 mA
= 8 mA
0.4
2.0
V
V
OL
OL
OL
V
Output High Voltage
I
= 1.9 mA (all ports 0,1,2,3)
2.4
V
OH
OH
Notes:
4. Power-on Reset occurs whenever the voltage on V is below approximately 2.5V.
CC
5. This is based on transitions every 2 full-speed bit times on average.
Document #: 38-08001 Rev. *B
Page 45 of 51
CY7C64013C
CY7C64113C
23.0
OSC
Electrical Characteristics (continued)
f
= 6 MHz; Operating Temperature = 0 to 70°C, V = 4.0V to 5.25V
CC
Parameter
Description
DAC Interface
Conditions
Min.
Max.
Unit
R
DAC Pull-up Resistance (typical 14 kΩ)
DAC[7:2] Sink current (0)
DAC[7:2] Sink current (F)
DAC[1:0] Sink current (0)
DAC[1:0] Sink current (F)
Programmed Isink Ratio: max/min
Tracking Ratio DAC[1:0] to DAC[7:2]
DAC Sink Current
8.0
0.1
0.5
1.6
8
24.0
0.3
1.5
4.8
24
kΩ
mA
mA
mA
mA
up
I
I
I
I
I
V
= 2.0V DC
= 2.0V DC
= 2.0V DC
= 2.0V DC
= 2.0V DC
sink0(0)
sink0(F)
sink1(0)
sink1(F)
range
out
V
out
V
out
V
out
V
4
6
out
[7]
T
V
= 2.0V
14
1.6
22
ratio
out
I
I
V
= 2.0V DC
4.8
0.6
mA
sinkDAC
lin
out
Differential Nonlinearity
DAC Port
LSB
24.0
Switching Characteristics (f
= 6.0 MHz)
OSC
Parameter
Description
Min.
Max.
Unit
Clock Source
f
t
t
t
Clock Rate
6 ±0.25%
166.25
MHz
ns
OSC
cyc
CH
Clock Period
167.08
Clock HIGH time
Clock LOW time
0.45 t
0.45 t
ns
CYC
CYC
ns
CL
USB Full Speed Signaling
t
t
t
t
Transition Rise Time
Transition Fall Time
4
4
20
20
ns
ns
rfs
ffs
Rise / Fall Time Matching; (t /t )
90
111
%
rfmfs
dratefs
r f
Full Speed Date Rate
12 ±0.25%
Mb/s
DAC Interface
Current Sink Response Time
HAPI Read Cycle Timing
t
0.8
µs
sink
t
t
t
t
Read Pulse Width
15
0
ns
ns
ns
ns
RD
OE LOW to Data Valid
40
20
60
OED
OEZ
OEDR
OE HIGH to Data High-Z
OE LOW to Data_Ready Deasserted
HAPI Write Cycle Timing
Write Strobe Width
t
t
t
t
15
5
ns
ns
ns
ns
WR
Data Valid to STB HIGH (Data Set-up Time)
DSTB
STBZ
STBLE
STB HIGH to Data High-Z (Data Hold Time)
15
0
STB LOW to Latch_Empty Deasserted
Timer Signals
50
t
Watchdog Timer Period
8.192
14.336
ms
watch
Notes:
6. Irange: I
(15)/ I
(0) for the same pin.
sinkn
sinkn
7.
8.
T
= I
[1:0](n)/I
[7:2](n) for the same n, programmed.
ratio
sink1
sink0
I
measured as largest step size vs. nominal according to measured full scale and zero programmed values.
lin
9. Per Table 7-6 of revision 1.1 of USB specification.
10. For 25-pF load.
11. Assumes chip select CS is asserted (LOW).
Document #: 38-08001 Rev. *B
Page 46 of 51
CY7C64013C
CY7C64113C
t
CYC
t
CH
CLOCK
t
CL
Figure 24-1. Clock Timing
t
t
r
r
D+
D−
90%
90%
10%
10%
Figure 24-2. USB Data Signal Timing
Interrupt Generated
Int
CS (P2.6, input)
OE (P2.5, input)
DATA (output)
tRD
D[23:0]
tOED
tOEZ
STB (P2.4, input)
tOEDR
(Ready)
DReadyPin (P2.3, output)
(Shown for DRDY Polarity=0)
Internal Write
Internal Addr
Port0
Figure 24-3. HAPI Read by External Interface from USB Microcontroller
Document #: 38-08001 Rev. *B
Page 47 of 51
CY7C64013C
CY7C64113C
Interrupt Generated
CS (P2.6, input)
Int
tWR
STB (P2.4, input)
tSTBZ
DATA (input)
D[23:0]
tDSTB
OE (P2.5, input)
tSTBLE
LEmptyPin (P2.2, output)
(Shown for LEMPTY Polarity=0)
(not empty)
Internal Read
Internal Addr
Port0
Figure 24-4. HAPI Write by External Device to USB Microcontroller
25.0
Ordering Information
Operating
Range
Ordering Code
PROM Size
8 KB
Package Type
28-Pin (300-Mil) SOIC
CY7C64013C-SXC
CY7C64013C-PXC
CY7C64013C-SXCT
CY7C64113C-PVXC
Commercial
Commercial
Commercial
Commercial
8 KB
28-Pin (300-Mil) PDIP
8 KB
28-Pin (300-Mil) SOIC - Tape Reel
48-Pin (300-Mil) SSOP
8 KB
Document #: 38-08001 Rev. *B
Page 48 of 51
CY7C64013C
CY7C64113C
26.0
Package Diagrams
48-Lead Shrunk Small Outline Package
51-85061-*C
28-Lead (300-Mil) PDIP
SEE LEAD END OPTION
14
1
MIN.
DIMENSIONS IN INCHES [MM]
MAX.
REFERENCE JEDEC MO-095
PACKAGE WEIGHT: 2.15 gms
0.260[6.60]
0.295[7.49]
15
28
0.030[0.76]
0.080[2.03]
SEATING PLANE
1.345[34.16]
1.385[35.18]
0.290[7.36]
0.325[8.25]
0.120[3.05]
0.140[3.55]
0.140[3.55]
0.190[4.82]
0.009[0.23]
0.012[0.30]
0.115[2.92]
0.160[4.06]
3° MIN.
0.015[0.38]
0.060[1.52]
0.055[1.39]
0.065[1.65]
0.310[7.87]
0.385[9.78]
0.090[2.28]
0.110[2.79]
0.015[0.38]
0.020[0.50]
SEE LEAD END OPTION
51-85014-*D
LEAD END OPTION
(LEAD #1, 14, 15 & 28)
Document #: 38-08001 Rev. *B
Page 49 of 51
CY7C64013C
CY7C64113C
26.0
Package Diagrams (continued)
28-Lead (300-Mil) Molded SOIC
NOTE :
PIN 1 ID
1. JEDEC STD REF MO-119
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH,BUT
DOES INCLUDE MOLD MISMATCH AND ARE MEASURED AT THE MOLD PARTING LINE.
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.010 in (0.254 mm) PER SIDE
14
1
MIN.
3. DIMENSIONS IN INCHES
MAX.
0.291[7.39]
0.300[7.62]
4. PACKAGE WEIGHT 0.85gms
*
0.394[10.01]
0.419[10.64]
PART #
15
28
0.026[0.66]
0.032[0.81]
S28.3 STANDARD PKG.
SZ28.3 LEAD FREE PKG.
SEATING PLANE
0.697[17.70]
0.713[18.11]
0.092[2.33]
0.105[2.67]
*
0.004[0.10]
0.0091[0.23]
0.0125[3.17]
0.015[0.38]
0.050[1.27]
0.013[0.33]
0.019[0.48]
*
0.004[0.10]
0.050[1.27]
TYP.
0.0118[0.30]
51-85026-*D
All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-08001 Rev. *B
Page 50 of 51
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implDiesotwhantlothaedmfarnoumfacWturwerwa.sSsuommeasnaullarilssk.cofosmuc.hAulsleMaannduinadlsoinSgesaoricnhdeAmnndifieDsoCwypnrelosasda.gainst all charges.
CY7C64013C
CY7C64113C
Document History Page
Document Title: CY7C64013C, CY7C64113C Full-Speed USB (12 Mbps) Function
Document Number: 38-08001
Issue
Date
Orig. of
Change
REV.
**
ECN NO.
109962
129715
Description of Change
12/16/01
02/05/04
SZV
Change from Spec number: 38-00626 to 38-08001
*A
MON
Added register bit definitions
Added default bit state of each register
Corrected the Schematic (location of the Pull up on D+)
Added register summary
Modified tables 19-1 and 19-2
Provided more explanation regarding locking/unlocking mechanism of the
mode register.
*B
429099
See ECN
TYJ
Changed part numbers to the ‘C’ types. Included ‘Cypress Perform’ logo.
Updated part numbers in the Ordering section.
Document #: 38-08001 Rev. *B
Page 51 of 51
|